Page - 11
There are two methods of disarming the MAX-EDP:
Disarming the System
Disarming the System Using
the Transmitter
2- The second method is an “Emergency Override” alternative, should
the transmitter become lost or inoperable. This method uses the Valet
Switch, but the vehicle’s ignition key is also required.
1- The primary method is to use the transmitter by pressing and releasing
its “disarm/unlock” button. This is the normal “daily use” method.
Press and release the transmitter’s “disarm/unlock” button once to
instantly disarm the system, disengaging the starter interrupt and unlock the
doors. If you have the optional unlock driver's door feature installed, then
upon disarming only the driver's door will unlock, and if the “disarm/unlock”
button is pressed again at anytime thereafter, all of the doors will unlock.
The system’s reaction: Disarming is confirmed by the siren chirping twice,
the Status Light turning off, and the parking lights flashing twice, then with
the interior lights illuminating for 30 seconds for approach illumination. The
lights will turn off instantly if the ignition switch is turned "on" before the 30
seconds expires.
Prewarning Detection Circuit: When the sensor is triggered by a light
impact or shock to the vehicle, the security system will respond by chirping
the siren 3 times and locking the doors. After this Prewarning circuit has
been triggered five times it will automatically shutdown until the alarm
system is disarmed, then armed.
If the MAX-EDP was activated and reset itself: The disarming confirmation
will no longer be 2 siren chirps, and the parking lights flashing twice before
staying on with the interior lights. Instead, the system will respond with 4
siren chirps and the parking and interior lights flashing 4 times before
staying on for 30 seconds. The Status Light will change to flashing two to
four times in red between pauses as a “Zone Violation” code to indicate
which protection circuit triggered the system (2 flashes, hood/trunk; 3
flashes, doors; 4 flashes , impact sensor). These special audible and visual
disarming indications, and Zone Violation code, will remain this way until the
ignition key is turned “on”.
Page - 34
Feature #11 Alarm Duration
Factory Default Setting
30 Seconds
(press “arm/lock” button to program)
Options:
60 Seconds
(press “disarm/unlock” button to program)
90 Seconds
(press
“
OPTION
”
button to program)
120 Seconds
(press red
“
panic
”
button to program)
This feature allows four choices of the Alarm Duration, which is the period
of time for which the system sounding the siren (and/or horn, optionally) and
flashes the parking lights when it is triggered. Caution: Before lengthen-
ing the Alarm Duration you should always check and determine if there
are any local anti-noise or nuisance ordinances in your area, to avoid
the possibility of receiving a violation citation.
Feature #12 Parking Light Illumination Upon Disarm
Factory Default Setting
On (press “arm/lock” button to program)
Option:
Off (press “disarm/unlock” button to program)
This feature affects the parking light operation when the system is dis-
armed. When this feature is turned on, the parking lights flash once, and
then turn back on for external illumination for 30 seconds unless the ignition
key is turned on during that time. If this feature is turned off, the parking
lights flash once only, and do not illuminate. This feature only affects the
MAX-EDP’s parking light operation, and not the interior light operation.
Feature #13 2nd Channel Also Disarms System
Factory Default Setting
On (press “arm/lock” button to program)
Option:
Off (press “disarm/unlock” button to program)
“2nd channel” is most commonly used to remotely open the vehicle’s trunk,
in which case the alarm should also disarm. This feature, turned on,
configures the system to disarm when the 2nd channel is used. If turned off,
the 2nd channel output will still occur, with 2 chirps, but without the parking
light flashes; and if armed, the system will not disarm.
Feature #14 3 or 45 Second Arming Delay
Factory Default Setting
3 Seconds
(press “arm/lock” button to program)
Options:
15 Seconds
(press “disarm/unlock” button to program)
30 Seconds
(press
“
OPTION
”
button to program)
45 Seconds
(press red
“
panic
”
button to program)
When the system is armed, whether by the transmitter, optional 2-way
controller or by an automatic feature, there is a brief period of time in which
