Violet Wire - (Positive Door Trigger):
The Violet wire is identical to
the Green Door Trigger wire, with the sole exception that it is an open door input
to the control module for vehicles having Positive 12 volt door pin switches.
Green Wire - (Negative Door Trigger):
The Green wire is an "open
door" input to the control module for vehicles having Negative switching door pin
switches. This wire is most commonly connected to the vehicle interior light
system.
CONNECTION:
Connect the Green wire to a wire in the vehicle that is
common to all the door pin switches; the correct wire in this type of interior or dome
light/door jamb pin switch system will have no voltage present and will also show
chassis ground when the doors are opened, and up to 12 volts when the doors are
closed.
Page - 11
12
12
12
12
12
12
12
1
1
1
1
1
1
1
12
12
12
12
12
12
1
1
1
1
1
1
1
1
1
1
1
1
1
Passenger
Pin
Switch
(+)12 Volts
Driver
Pin
Switch
The Driver Pin Switch will often have
an extra wire that activates the “ignition
key in switch” warning chime. This
circuit will activate the security system,
but only from the driver's door, and is
the incorrect trigger wire >
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
123456789012
Interior Light
Typical Negative Switching Interior Light System
This is the
correct "trigger”
wire - connection
may be made at
any point
)
1
1
1
1
1
1
1
Driver
Pin
Switch
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
1234567890123
To Chassis
Ground
Interior
Light
To Constant
12 Volt
Note: The Driver Pin Switch
will often have an extra wire;
this circuit will activate the se-
curity system, but only from the
driver's door. This is the incor-
rect activation wire >
Passenger
Pin
Switch
This is
the correct
“trigger” wire
- connection
may be made at
any point
Typical Positive Switching Interior Light System
)
Feature #3 Automatic Rearming
Factory Default Setting
Off
(
press
“arm/lock” button to program
)
Options:
On without doors locking
(
press
“disarm/unlock” button to program
)
On with doors locking
(
press
“
II
” button to program
)
“Automatic Rearming” prevents the system from becoming accidentally disarmed
by having it arm itself after being disarmed, if a door is not then opened or the
ignition turned on. Options are to have Automatic Rearming operate with or
without also locking the doors when the system does rearm.
Feature #4 Starter Interrupt Functions
Factory Default Setting
On
(
press
“arm/lock” button to program
)
Options:
Off
(
press
“disarm/unlock” button to program
)
Automatic
(
press
“
II
” button to program
)
This feature controls the Starter Interrupt circuit, in several ways. In its default
setting, “On”, the Starter Interrupt is operable whenever the alarm is armed.
The “Automatic” option will cause the Starter Interrupt output to automati-
cally engage 90 seconds after the ignition switch is turned "off", and also 90 sec-
onds after disarming the system. This automatic engagement will occur even if the
security system is in a disarmed state, but not if it is in Valet Mode. Once the
Starter Interrupt output is activated, the system must be armed, then disarmed with
the controller or transmitter, or placed into the Valet Mode by pressing and hold-
ing the Valet Switch for 2 seconds to disengage it. There are no Status Light
indications with this automatic form of Starter Interrupt.
Programming this feature “Off” completely eliminates the Starter Interrupt
output, while leaving all other system operations fully functional.
Feature #5 Ignition Activated Override
Factory Default Setting
Off (
press
“disarm/unlock” button to program
)
Option:
On (
press
“arm/lock” button to program
)
This feature allows an activated system to be overridden and disarmed by simply
turning th
e i
gnition switch on within 10 seconds of the system’s activation. After
10 seconds, the Emergency Override must be performed or the controller or trans-
mitter “disarm/unlock” button can be used to disarm the system.
Page - 26
Feature #6 Doors Lock With Ignition On
Factory Default Setting
On (
press
“arm/lock” button to program
)
Option:
Off (
press
“disarm/unlock” button to program
)
This feature configures the system to automatically lock the vehicle’s doors every
