OMC CA-110912 Use & Care Manual Download Page 8

7

7

www.omcbbq.com

8

MAIN BURNER

USING THE IGNITOR (Figure 11A)

1. Open the lid before lighting.
2. Turn off all of the burner control knobs and

close the gas supply valve.

3. Open the gas supply valve and wait 5

seconds.

4. Push in and turn a single main burner

control knob to ‘HIGH’. All other control
knobs should be in the "OFF" position. 

5. Depress the ignitor, repeat if necessary.
6. If the burner does not light immediately

(within four seconds), turn burner
control knob off and wait 5 minutes to clear the gas.

7. Repeat steps 1 to 6. If burner still fails to light, refer to

Troubleshooting Guide

to determine cause and solution, or try the

Match Lighting procedure below.

MATCH LIGHTING PROCEDURE

1. Open the lid before lighting.
2  Place an ignited lighter or lit match

through the lighting hole, approx. 1.25 cm
(1/2") from burner. (See Figure 11B)

3. Push in and turn the left burner control

knob to ‘HIGH’. The burner should light
immediately (within four seconds). If it does not, extinguish the
lighter or match, turn the control knob to off, and wait 5 minutes to
clear the gas. 

4.  Repeat steps 1 to 3. If burner fails to light, refer to the

Troubleshooting Guide to determine cause and solution.

LIGHTING THE OTHER SIDE OF THE DUAL BURNER

Once one side of the dual burner has been lit, push in and turn the other
control knob to ‘HIGH’. The unlit burner will light automatically.

SIDE BURNER (OPTIONAL)

USING THE IGNITOR

1. If sideburner has a lid, raise side burner

lid before lighting.

2.  Push in and turn the side burner control

knob to 'HIGH'.

3. Turn or depress ignitor. Repeat if

necessary (see Figure 12A).

4. If burner does not light immediately

(within four seconds), turn the burner
control knob off, and wait 5 minutes to clear the gas.

5.  Repeat steps 1 to 4. If burner still fails to light, refer to the

Troubleshooting Guide to determine cause and solution, or try the
match lighting procedure below.

MATCH LIGHTING PROCEDURE

1. If Sideburner has a lid, raise side

burner lid before lighting.

2. Place an ignited lighter or lit

match near the ports,
approximately 1.25 cm (1/2")
from burner (see Figure 12B).

3. Push in and turn the side burner

control knob to 'HIGH'. The
burner should light immediately
(within four seconds). If it does not, extinguish the lighter or match,
turn the control knob off, and wait 5 minutes for the gas to clear.

4. Repeat steps 2 and 3. If burner still fails to light, refer to the

Troubleshooting Guide to 
determine the cause and solution.

HIGH

LOW

Fig. 10

PROPANE MODELS ONLY

If the heat output from the burner(s) seem abnormally low, it may be
caused by the regulator flow-limiting device being activated by a leak in
the gas system, or improper lighting procedures. If this is suspected,
shut off the cylinder valve and all burner valves. Perform a leak test to
determine if a leak has caused the flow-limiting device to activate. If the
leak test is negative, then carefully follow the lighting procedures step-
by-step, ensuring all valves (including tank) are 

off

before starting.

RELIGHTING

SAFETY WARNING

If the burner flame goes out when your barbeque is in operation,
immediately turn off the control valves. Wait five minutes for the gas to clear
before attempting to relight the burner. If the problem persists, refer to the
Troubleshooting Guide.

SHUTTING DOWN YOUR BARBEQUE

1. Shut off L.P. cylinder valve.
2. Shut off burner control valves.
This sequence prevents residual gas from being left in the system under
pressure.

BREAKING IN YOUR BARBEQUE

Before cooking on your gas barbeque for the first time, you should "break
it in" by operating it for a short period of time without any food. To "break
in" your barbeque light the barbeque following the lighting instructions as
outlined on the console decal or in this manual. (see page 7).  Close the
lid and keep the temperature on "HIGH" for 20 minutes. 

DO NOT OPEN

THE LID DURING THIS PROCESS. 

Then raise the lid and continue to

operate your barbeque on "HIGH" for an additional 5 minutes. Your
barbeque is now ready for cooking. 

NOTE: FOR LAVA ROCK MODELS ONLY

DO NOT OPERATE YOUR BARBEQUE IF THE LAVA ROCKS ARE WET,
THE BUILD-UP OF STEAM MAY CAUSE THEM TO FRAGMENT.

NOTE: FOR FLAV-R-WAVE™ (HEAT DISTRIBUTION PLATE)
MODELS ONLY

LAVA ROCK IS NOT REQUIRED AND IS NOT TO BE USED IN THIS SYSTEM.
THE USE OF LAVA ROCK OR CERAMIC ROCK WITH FLAV-R-WAVE™
(HEAT DISTRIBUTION PLATE) IS EXTREMELY UNSAFE AND COULD 
RESULT IN SERIOUS BODILY INJURY AND/OR PROPERTY DAMAGE.

Fig. 11B

NOTE: WHEN USING THE SIDE
BURNER, THE MAXIMUM POT
SIZE IS 9" WIDE.

MAX

NOTE: MAXIMUM
WEIGHT FOR SIDE
BURNER 10 lb  (4.5 kg)

SIDE BURNER COOKING POTS

WARNING

!

DO NOT LIGHT SIDE BURNER WITH LID
DOWN. FAILURE TO DO SO MAY CAUSE
SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE.

2.

2.

Fig. 12A

WARNING

!

IF SIDE BURNER IS EQUIPED WITH LID:
DO NOT LIGHT SIDE BURNER WITH LID
DOWN. FAILURE TO DO SO MAY CAUSE
SERIOUS BODILY INJURY AND/OR
PROPERTY DAMAGE.

1.

4.

5.

5.

Fig. 11A

4.

1.25 cm

Fig. 12B

NOTE: MAXIMUM WEIGHT FOR SIDE
BURNER 9kg (20 lb)

Summary of Contents for CA-110912

























Reviews: