Selection BA MO B+R
Mounting instructions for installers and
appliance fitters
Important:
Read these instructions thoroughly before
installing the appliance. Determine the precise position in
the salon with the salon owner and the installation
specialist.
•
The wash unit is intended for operation in clean and
dry rooms at normal room temperature.
•
In the water supply system only original components
supplied by the manufacturer must be used.
•
The wash unit must only be connected to a water
supply where the supply pressure does not exceed
20 bar (20 MP a).
•
The new set of hoses supplied with the unit must be
used. Old hoses must not be used.
1.
The water supply pipes to the wash unit must be
equipped with an “Aqua-Stop” system.
2.
Place the
mounting template
at the determined
position and use it to drill the required holes.
Observe the notes on the mounting template!
3.
Make the holes for cold water (
K
), hot water (
W
)
and waste water (
A
).
4.
Route
½"
pipes for the hot and cold water supply
and 40 mm dia. drain pipe with connecting sleeve for
the siphon through the floor.
5.
Ensure that the stop valves and siphon are at the
correct position and correctly spaced (see the
mounting template).
6.
Height of the connecting pipes and drain pipe:
½" pipe: 50 mm above finished floor 40 mm dia. drain
pipe: 50 mm above finished floor
13.
Make sure that pipes/pressure hoses and drain hose
are parallel. Connect the unit.
Prevent the stop
valves from turning while they are being
screwed on
. Connect the waste water hose to the
siphon using a seal and union nut. Insert the waste
water hose at least 3 to 4 cm into the siphon. Connect
the drain bushing to the waste water hose using a hose
clamp.
14.
Close the mixing tap. Open the stop valve and check
for leaks with the mixing tap closed. Check the mixed
water. The hot water and cold water supply must
correspond to the coloured symbols
on the mixing tap.
15. Check the pressure of the unit with 8 bar water
pressure. Then set the pressure to 3 to 5 bar. On
completion of the installation work, always rinse out
the water pipes. A central regulating tap is required if
more than one unit is installed. This tap must be easily
accessible from the salon.
Mounting instructions for installers, appliance
fitters and electricians
These mounting instructions apply to the connection
of one unit.
If more than one unit is to be installed, the pipe
cross section must be increased
accordingly.
Important:
If the water pressure is above 5 bar, it must be
regulated by a pressure reduction valve. Since a pressure
reduction valve is used for boilers, such a valve can be fitted
along the common water
supply line.
Note for salon owners:
The connections described under points 1 to 6 and 13 to 15
must be performed by the installer. The installer is responsible
for any problems that may occur. The manufacturer of the unit
shall not accept warranty claims for this work.
7.
Removing inspection door (5): grasp the opening at the
top, pull back and lift out from the bottom.
Removing housing components from the front assembly
(3+4): Unscrew each of the 2 hexagon socket-head
screws in the column housing (1) and pull off the housing
components as shown in
fig. 3
8.
Only for in-line installation:
Prepare the cover sections (1+2) for connection of the
installation shaft (
Fig. 2
):
- Cut out a 120 mm dia. section as shown in the
illustration
- Make sure that the mounting side corresponds to that
shown in the installation diagram.
9.
Align the substructure (6) according to the installation
template and secure to the floor.
4 anchor bolts M 10 x 125 (extending 30 mm above the
finished floor) or metal plugs with metric thread for
hexagonal screws M 10 x 60.
10. Only for in-line installation:
- Attach 2 angled mounting brackets for the installation
duct at each column housing (Fig. 2)
Caution:
- Attach brackets inside the installation duct!
- Duct ends must be protected with edge covers!
Mount lower part of duct. Place upper part of duct on
top.
11. Attach towel holder (9) - if ordered:
Attach the towel holder each with 2 M6X12 cylinder
head screws and washers from inside through the bore-
holes on the column housing (1) and screw tightly.
12. Attach oddments tray (10) - where ordered:
Fit M5 threaded sleeves from outside into the boreholes
of the column housings (1 + 2). Screw in 2 knurled screws
M5x20 until location 5 mm from the housing is reached.
Place oddment tray with the oval holes onto the knurled
screws and screw tight with the knurled screws.
GB
