![background image](http://html.mh-extra.com/html/olt/8x12-spacemaker-garden-shed/8x12-spacemaker-garden-shed_assembly-manual_732311002.webp)
Thank you for purchasing our 8x12 SpaceMaker Garden Shed (Metal Roof).
Please take the time to identify all the parts prior to assembly.
Parts List:
A. Floor Section
3 - 45 1/2” x 75” Floor - Joist Frames
6 - 1 1/2” x 3 1/2” x 71 3/4” - Center Floor Joists - Unattached
3 - 45 1/2” x 21” - Floor Joist Frames
3 - 45 3/8” x 74 7/8 - Plywood Floor - Large
3 - 45 3/8” x 20 7/8” - Plywood Floor - Small
10- 1 1/2” x 3 1/2” x 68 3/16”- Floor Runners
B. Wall Section
7 - 45 1/2” x 75” - Solid Wall Panels
7 - 1 1/2” x 2 1//2 x 45 1/2” Bottom Wall Plates
1 - 45 1/2” x 75” - Window Wall Panel
2 - 12” x 73” - Narrow Wall Panels
Door Jambs & Header
2 - 1 1/2” x 3” x 73” - Vertical Door Jamb
1 - 2” x 3” x 78” - Door Header
2 - 2” x 3” x 6 1/2” - Door Header End Plates
1 - Left Side Door
1 - Right Side Door
2 - 2 1/2” x 1/2” x 72” - Interior Vertical Door Stops
1 - 2 1/2” x 1/2” x 68” - Interior Top Horizontal Door Stop
1 - 2 1/2” x 3/4” x 62 1/2” - Door Threshold
1 - 1/2” x 2 1/2” x 71” - Interior Door Flange
Top Wall Plates
6- 3/4” x 2 1/2” x 32” - Front & Rear Top Plates
(4 pcs angle cut one end, 2 pcs straight cut both ends)
4 - 3/4” x 2 1/2” x 65 3/4” - Side Top Plates (Angle cut edge)
Gable Walls
4 - Gable Half Walls - Triangular Shaped
C. Rafter Section
18- 1 1/2” x 3 1/2” x 56 1/2” - Roof Rafters
2 - 3/4” x 4 1/2” x 84” - Roof Ridge Boards
2 - 3/4” x 4 1/2” x 52 1/2” - Roof Ridge Boards
2 - 1/16” x 3” x 7” - Metal Ridge Board Connectors
4 - 1/2” x 4 1/2” x 68 1/4” - Soffits
D. Roof Section
8 - 3/4” x 3 1/2” x 49 1/2” Roof Batten (outside)
4 - 3/4” x 3 1/2” x 45 3/8” Roof Batten (middle)
8 - 3/4” x 3 1/2” x 72 3/8” Roof Batten (center)
8 - 58”long x 39” wide Metal Roof Panels
3 -3/4” x 3 1/2” x 72” Roof Gussets - (angle cut on ends)
4 - 3/4” x 2 1/2” x 48” Facia/Roof Nailing Strips
3 - 13”w x 60” Metal Ridge Cap
Several Strips of Foam Enclosures for Metal Roof Ends
E. Miscellaneous Section
Bottom Skirting
10 - 1/2” x4 1/2” x 45 1/4” - Side Bottom Skirting
Corner & Sidewall Trim
8 - 1/2”x 2 1/2” x 79” - Narrow Trims
3 - 1/2” x 2 1/2” x 77 1/2” - Doorway / Rear Wall Trims
4 - 1/2” x 2 1/2” x 75” - Filler Trim
4 - 1/2” x 4 1/2” x 82” - Wide Corner Trim
4 - 1/2” x 4 1/2” x 44 1/2” - Horizontal Gable Trim
Facia Trim
4 - 3/4” x 3 1/2” x 58” long - Front and Rear Facia
(Angle cut on ends - 2 right / 2 left)
4 - 3/4” x 3 1/2” x 71 3/4” long - Side Facia)
Misc. Pieces
1 - Window Insert
1 -Window Trim Pkg - (1-24 1/16” angle cut / 3 -23” straight cut)
1 - Flower Box Kits
2- Pentagon Facia Plate (for front/rear)
2 -Facia Detail Plates 3 1/2” high
2- Gable Facia Plates 4 1/2” high
1 pc - Spare Wall Siding
2 pcs - Spare Shingles- use to shim door, etc
Note: We recommend you drill a 1/8” pilot hole for each screw, to
avoid splitting wood. The hole depth should be equal to 3/4 the length
of screw.
Toll Free 1-888-658-1658 www.outdoorlivingtoday.com [email protected]
Page 2
Note: All Trim, Facia and Bottom Skirting pieces will be positioned rough face out when installed.
Advice:
Wood has a tendancy to split when
screwing near the ends of a board. To prevent
splitting, it is always recommended to pre-drill
pilot holes before screwing into these areas.