60
Inverter swimming pool heat pump
GB
Step 1: Detach the control unit from the equipment. Pay attention to the communication
wire connected to the printed circuit board and separate it carefully.
Step 2: Use a screwdriver to open the casing and remove the control unit.
Step 3: Drill two parallel holes at eye level: 60 mm centre distance.
Step 4: Attach the rear cover panel of the control unit to the wall.
Step 5: Align the front and rear covers carefully, and make sure the box
is fi rmly fi xed to the wall.
Step 6: Connect the communication wire carefully.
Step 1
Step 3
Step 5
Step 2
Step 4
Step 6
Wall mounting the
control unit
3.9
IMPORTANT:
Do not use sharp objects when touching the front panel and the buttons of the
control unit as you might damage them. When the control unit is fi xed to the wall,
do not pull the communication wire. This could loosen the wiring and damage
the contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
16
3.9 Wall-mounting the remote control
Step 1:
Detach the remote control from the machine. Pay attention to the communication wire connected to the
printed circuit board and separate them carefully.
Step 2:
Use a screwdriver to open the casing and separate the remote control.
Step 3:
Drill two parallel holes at eye level: 60 mm centre-to-centre.
Step 4:
Attach the remote control’s rear cover to the wall.
Step 5:
Align the front and rear covers exactly, ensuring that the box is fixed firmly to the wall.
Step 6:
Carefully connect the communication wire.
WARNING: Do not use sharp objects to touch the remote control’s front face and buttons as you
may damage it. When the remote control is fixed to the wall, do not pull the communication wire,
this may cause a loose contact.
