Octalarm T16 User Manual Download Page 24 | Manualshive

Page: 24 / 56

background image

Operation instructions

Adesys bv, Wateringen, NL

24

Octalarm-T2 / T4 / T8 / T16

15. ERROR MESSAGES

Installation or set-up errors may give the following error messages:

Display messages

Cause

Solution

BATTERY FAULT,
REPLACE BATTERY

The Octalarm has detected that the
emergency battery capacity has dropped
below 30% of the original value. There is a
possibility that a telephone warning of a
network error cannot be passed on.

Have the battery replaced
by professionals.

SHORTCIRCUIT IN
THE SENSOR
NETWORK

A short-circuit has been detected in the
Sensor network cable.

Check the cable circuits.

TELEPHONE
CONNECTION
DEFECTIVE

There is no power on the telephone line,
owing to a failure, or is dropping to an
extremely low value during the use of another
machine or peripheral connected to the same
line.

Check the telephone line.
The telephone line
monitoring can be
switched off, see also
prog. 41 “adjusting the
dialler”.

SETUP ERROR ISDN
CALL NUMBER XX

A message has been sent to a non-existent
ISDN call number.

Check the call number
installed.

ISDN S-BUS
DEFECTIVE

The Octalarm has detected that there is no
power on the ISDN line (i.e. the S box).

Check the ISDN line and
the ISDN connection
cables.

ISDN NETWORK
ERROR XX

There is a failure in the service provider’s
ISDN network.

Wait for a while to see
whether the failure
continues. If it does,
contact your service
provider.

ISDN MODULE
DEFECTIVE

The inbuilt ISDN module is defective.

Send the Octalarm to be
repaired.

GSM NETWORK: NO
INCOMING SIGNAL

There is no connection with the mobile
network, possibly because of a fault in the
network or because the antenna is defective
or not properly placed.

Check whether the mobile
network is present. If it is,
check and/or move the
antenna.

GSM:
NO SIM CARD

No SIM card has been inserted, or the
inserted card is not recognized.

Check the SIM card under
the protective cover.

GSM BLOCKED! PIN
CODE INCORRECT!

An incorrect PIN code has been entered,
blocking the SIM card.

Unblock the SIM card,
see prog. 41, “adjusting
the dialler”.

GSM MODULE
DEFECTIVE

The inbuilt GSM module is defective.

Send the Octalarm to be
repaired.

«
...
22
23
24
25
26
...
»

Summary of Contents for T16

























































Reviews:

No comments

Related manuals for T16

BL-C1A - Network Camera

Brand: Panasonic Pages: 4

Brand: Panasonic Pages: 40

Brand: Panasonic Pages: 56

Brand: Panasonic Pages: 8

Brand: YORKVILLE Pages: 17

Brand: Cambridge SoundWorks Pages: 20

Brand: JBL Pages: 24

Brand: Olympus Pages: 374

Brand: Olympus Pages: 66

Brand: Vectaire Pages: 2

Brand: Q Acoustics Pages: 19

Brand: Uniden Pages: 42

Brand: Zeck Audio Pages: 16

Brand: IDEC Pages: 6

Brand: Sincro Pages: 24

Brand: Toa Pages: 16

Pack TYXAL+ Access

Brand: DELTA DORE Pages: 11

Brand: ESAB Pages: 20

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands