Operating Instruction and Documentation
2.60 HL SST
- 22 -
Pic 9:
Use the extended threaded socket connection
and turn clockwise with an appropriate tool
(socket wrench size 24, available at your
dealer,). Lower the lifting carriage only 5cm –
10 cm. Repeat this process on the next column
and continue until the entire lift is in its lowest
position. Only lower each side 5 cm-10 cm at a
time.
Repair the defective lift. After this is complete, a
“Reset” must be carried out (described in the
operating instructions).
Attention!! Lower the automotive-lift only approx. 5cm – 10 cm at a time.
Observe the complete emergency lowering process.
Do not work with the lift until the defective parts are changed.
Recommencement of work can only begin once the lift is deemed to be in perfect
condition regarding safety.
• If the lift has been deemed safe to operate, carry out a reset as described in the operating
instructions.
6.3 Reset after an emergency lowering
A reset can only be carried out, if the automotive-lift is in its lowest position (fully
collapsed).
Access to the DIP-Switch is only possible once the main switch is in the “off”
position. Only instructed, authorized technical personnel can carry out the
reset.
a) Drive the vehicle off the lift.
b) Open the cover of the operating unit.
c) Open the electrical box door.
d) Press the button “Reset” 1 (see pic.5) and hold it.
e) Switch-off the main switch and wait 5 sec while holding the reset button.
f) Switch-on the main switch and wait 5 sec while holding the reset button.
g) Let go of the reset button
h) Press the button “lowering” until both lifting carriages are in their lowest position.
i) If necessary repeat steps d) to h) several times to be sure that the lift is in its lowest position.
j) Next, move the Dip-switch 7 to the “on” position.
k) Keep Dip-switch 5 in the “on” position.
l) Repeat the steps d) to h)
m) Next, move Dip-switch 7 to the “off” position. Keep Dip-switch 5 in the “on” position.
n) Three diodes should now light up on the computer-board. One additional diode should be
blinking in the frequency of approx. 1 sec.
Summary of Contents for 2.60 HL SST
