NuAire LabGard ES NU-543-300S Operation And Maintenance Manual Download Page 61 | Manualshive

Page: 61 / 72

background image

OM0239

Page 61 of 72

April 2021

9.0

Remote Contacts

The NU-543S has several contact closures for remote sensing of various functions.

9.1 Fan Relay

The fan relay contacts are normally open and closed contact closure outputs that are activated whenever the blower key is
pressed and the blower key LED indicator is on or blinking. Contact ratings are 250 VAC maximum at 2 Amps.

9.2 Alarm Relay

The alarm relay contacts are normally open and closed contact closure outputs which are activated whenever an airflow
alarm condition occurs. Contact ratings are 250 VAC maximum at 2 Amps.

9.3 15VDC Output

The 15VDC (100mA) output is active when power is applied to the

FlowGard™

control board.

«
...
59
60
61
62
63
...
»

Summary of Contents for LabGard ES NU-543-300S









































































Reviews:

No comments

Related manuals for LabGard ES NU-543-300S

Brand: Taylor Made Pages: 2

Brand: York Fitness Pages: 18

Brand: Safco Pages: 2

Brand: Omni Pages: 193

Brand: ACE INSTRUMENTS Pages: 15

Brand: Wave Fitness Pages: 15

Brand: Abicor Binzel Pages: 92

Brand: Daktronics Pages: 30

Brand: DAKOTA ULTRASONICS Pages: 28

Brand: Hagie Pages: 141

Brand: LAPPSET Pages: 16

Brand: MAGIC FX Pages: 25

Brand: Palmer Pages: 2

Brand: Harken Pages: 4

TR 2B INC INT NC

Brand: OMGA Pages: 76

Brand: York Fitness Pages: 18

Brand: 4B Pages: 16

Brand: FitEngine Pages: 68

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands