NuAire LabGard ES NU-543-300S Operation And Maintenance Manual Download Page 47

Page: 47 / 72

OM0239

Page 47 of 72

April 2021

7.5.4.5

Nite Care Calibration

The Nite Care mode is defaulted to operate the blower at approximately 600 rpm or a 14% duty cycle.
However, if desired the Nite Care blower speed can be adjusted higher or lower by performing the following:

•

Press and hold key, then press ENT

↑ and ↓ keys sequentially releasing the key after

the 3 key sequence.

The following service parameter display should appear

•

Press ↑ and ↓ to select calibration

•

Select and press ENT key for blower speed calibration

•

Select and press ENT key for Nite Care

Adjust blower speed with ↑ (increase) and ↓ (decrease) as needed.

•

Press ENT key to accept Nite Care blower speed calibration

Recommended Measurement Methods for Cabinet Downflow and Inflow Downflow Measurement

A. Instruments: TSI 8355 Thermo anemometer
B. Procedure:

Supply filter efflux is measured on a grid, in a horizontal plane 4 inches (102mm) above the bottom edge of the window.

Measurements should be taken over a period of at least 1 minute for each position.

C. Primary Test Data - Inches (mm):

300S

4.297 (109)

12.891 (327)

21.485 (546)

30.078 (764)

400S

5.797 (147)

17.391 (442)

28.985 (736)

40.578 (1031)

500S

7.297 (185)

21.891 (556)

36.485 (927)

51.078 (1297)

600S

8.797 (223)

26.391 (670)

43.985 (1117)

61.578 (1564)

6.31 (160)

18.93 (481)

Number of Readings:

Average Velocity

ft./min. m/s

Service Parameters

Configuration
Setpoints

Calibration

Options

Nite Care Blower Configuration

.41 600 rpm, 14.0%

fpm, 26.0⁰

Settling time

Summary of Contents for LabGard ES NU-543-300S









































































Search results

Summary of Contents for LabGard ES NU-543-300S

Reviews:

Related manuals for LabGard ES NU-543-300S

Brands by name

Popular brands

NuAire LabGard ES NU-543-300S, Operation And Maintenance Manual

Search results

Summary of Contents for LabGard ES NU-543-300S

Reviews:

Related manuals for LabGard ES NU-543-300S

Brands by name

Popular brands