NuAire LabGard ES NU-543-300S Operation And Maintenance Manual Download Page 6 | Manualshive

Page: 6 / 72

background image

OM0239

Page 6 of 72

April 2021

1.2 Safety Instructions

These safety instructions describe the safety features of the LabGard® ES Model NU-543S LFBSC.
The safety cabinet has been manufactured using the latest technological developments and has been thoroughly tested
before delivery. However, the cabinet may present potential hazards if it is not installed and used as instructed for its
intended purpose or is used outside of operating parameters. Therefore, the following procedures must always be
observed:

•

The safety cabinet must be operated only by trained and authorized personnel.

•

For any operation of this cabinet, the operator must prepare clear and concise written instructions for operating
and cleaning, utilizing applicable safety data sheets, plant hygiene guidelines, and technical regulations, in
particular.

o

Which decontamination measures are to be applied for the cabinet and accessories

o

Which protective measures apply while specific agents are used

o

Which measures are to be taken in the case of an accident

•

Repairs to the device must be carried out only by trained and authorized expert personnel.

•

Keep these operating instructions close to the cabinet so that safety instructions and important information are
always accessible.

•

Should you encounter problems that are not detailed adequately in the operating instructions, please contact your
NuAire Representative of NuAire technical Services.

1.3 Explanation of Symbols

CAUTION used without the safety alert symbol indicates a potentially
hazardous situation which, if not avoided, may result in property

damage.

Potential electrical hazard, only qualified person to access.

Note:

Used for important

information.

Biohazard

Ground, Earth

CAUTION



Chemical Hazard

Flammable Hazard

Hazardous Gases! Personal
Protection Equipment Required.

Lead Free

Safety alert symbol indicates a potentially hazardous
situation which, if not avoided, could result in death of
serious injury.

Safety alert symbol indicates a potentially hazardous
situation which, if not avoided, may result in minor or
moderate injury.

WARNING

!

CAUTION

!

«
...
4
5
6
7
8
...
»

Summary of Contents for LabGard ES NU-543-300S









































































Reviews:

No comments

Related manuals for LabGard ES NU-543-300S

Brand: B&K Pages: 8

Brand: GE Pages: 242

Brand: GE Pages: 24

Brand: Balanced Body Pages: 3

Brand: Walker Bay Pages: 8

Brand: JB-Lighting Pages: 60

Brand: Campbell Pages: 2

Brand: Major Pages: 52

Brand: Pari Pages: 50

Brand: Icare Pages: 42

Brand: YMC Pages: 49

Brand: Octane Fitness Pages: 8

Brand: Octane Fitness Pages: 10

Brand: OCENCO Pages: 48

Brand: Ocean Optics Pages: 6

Brand: RainPoint Pages: 40

Brand: FARM-MAXX Pages: 35

Brand: Martin Pages: 202

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands