126
Novell iFolder 3.x Administration Guide
no
vd
ocx (
E
NU)
01
F
ebr
ua
ry
200
6
B.3 Configuring iFolder 3.
x
Services on an NCS
for Linux Cluster
The following procedure describes how to configure Novell iFolder 3.
x
services on an NCS for
Linux cluster. You can optionally add iFolder 3.
x
Web Access services to the cluster.
1
On one of the nodes (Node 1), set up a shared volume to use for storing iFolder data.
This can either be a SAN or iSCSI volume. For information, see
“Setting Up Novell Cluster
Services” (http://www.novell.com/documentation/oes/cluster_admin_lx/data/h2mdblj1.html)
in the
OES Novell Cluster Services 1.8 Administration Guide for Linux
.
IMPORTANT:
Do not create a Cluster Resource at this time; it is configured after you finish
setting up iFolder services on the cluster.
2
Share the same Apache SSL certificate between all of the nodes.
For information, see
Section C.4, “Configuring Apache to Point to an SSL Certificate on a
Shared Volume for an iFolder Cluster,” on page 135
.
2a
Get key and certificate for the cluster’s highly available DNS name.
For information, see
“Managing SSL Certificates for Apache” on page 133
.
2b
On Node 1: Mount the shared volume, then copy the key and certificate files to the
cluster’s shared volume.
2c
On each node: Modify the node’s Apache SSL configuration file to point to the key and
certificate files on the shared volume.
3
For each node in the cluster, install iFolder services:
3a
In YaST, install iFolder 3 and iFolder 3 Web Access (optional), but do not configure
services at this time.
For information, see
Section 6.1, “Installing iFolder on an Existing OES Linux Server,” on
page 51
.
3b
Repeat the install on each node in the cluster, then continue with
Step 4
.
4
Configure iFolder services Node 1 by doing the following:
In the following commands, replace
/mnt/ifolder3
with the mount point of the shared
volume you created in
Step 1
.
4a
Mount the shared volume that you created in
Step 1
. At a server console, enter
mnt
/dev/sda1
/mnt/ifolder3
Replace
/dev/sda1
with the disk or partition containing the file system.
4b
In YaSt, configure the iFolder 3 enterprise server.
For information, see
Section 6.2, “Configuring the iFolder Enterprise Server,” on page 53
.
For the System Store Path, specify the mount point of the shared volume that you created
in
Step 1
.
At the end of the configuration, allow YaST to start Apache, then open your Web browser
to the iFolder server to make sure it is running.
http://
192.168.1.1
/simias10/Simias.asmx
Replace
192.168.1.1
with the IP address of the server node you are configuring. If
everything is working properly, you should get an authentication prompt.
Summary of Contents for IFOLDER 3 - ADMINISTRATION
