manualshive.com logo in svg

Norwood The Grain Handler 10, Operator'S Manual, Page: 109 / 130

Share
Download
Norwood The Grain Handler 10 Operator'S Manual Download Page 109

6 - TROUBLESHOOTING

6-1

6.0 - TROUBLESHOOTING

    

DANGER

NEVER ENTER BIN UNLESS ALL POWER IS LOCKED 

OUT AND ANOTHER PERSON IS PRESENT.

Exposed auger and moving parts can cause severe 

injury or death. Rotating augers are dangerous!  

Flowing grain may trap and suffocate.

FAILURE TO HEED THIS WARNING MAY CAUSE SE-

RIOUS INJURY OR DEATH.

          

    

DANGER

ROTATING AUGER HAZARD KEEP AWAY 

To prevent serious injury or death from rotating 

augers: 

1.   Do not enter bin unless power is locked out. 

2.   Turn machine OFF, shut down and lock out power 

source, unplug power cord and wait for all moving 

parts to stop before inspecting, servicing or repairing 

machine.

3.   Keep body, hair, and clothing away from moving parts.

4.   Stay away from rotating augers. Keep others away.

FAILURE TO HEED THIS WARNING MAY CAUSE 

SERIOUS INJURY OR DEATH.

Troubleshooting Field Problems

Problem

Possible Cause

Solution

Auger  will  not  start 

rotating.

No Power.

Turn power on at master panel.
Check fuses at master panel.

No grain flow.

Sump Plugged.

Empty bin and clean out sump. Remove trash 

from top of grain before starting.

Sump Empty.

Open other sump(s).

Bin empty.

Start Power Sweep auger

Sump closed.

Open slider gates.

Slow  grain  flow  from 

powerhead discharge.

Obstruction in sweep.

Remove obstruction.

Damaged or bent flighting.

Repair or bend flighting back to original shape. 

If this doesn’t work, replace flighting

Sweep is touching floor or drive wheel is not 

adjusted properly

Adjust  sweep  and  ensure  drive  wheel  is  in 

working condition

Gearbox  won’t  engage 

Power Sweep

Gearbox shift lever isn’t adjusted correctly.

Adjust lever to proper position. 

(See"Install The 

"Power Sweep Engagement Lever"" on page 

3-9)

Unload auger isn’t set on spline correctly.

Loosen powerhead and push auger onto gearbox 

spline. 

(See"Horizontal Powerhead Installation 

Step # 8" on page 3-19)

Gearbox  won’t  stay 

engaged

Power Sweep engagement lever moving from  

"Engage" position.

Adjust shaft collar towards lever and re tighten. 

(See"Install The "Power Sweep Engagement 

Lever"" on page 3-9)

Summary of Contents for The Grain Handler 10



































































































































Reviews:

No comments