Northern Telecom Compact ICS 4.0 Manual Download

Page: 165 / 254

Programming Hunt Groups / 153

P0881596 Issue 02

Compact ICS 4.0 System Coordinator Guide

In the latter case, the call is routed to the overflow position.
Once a call goes to the overflow position it is no longer a Hunt
Group call.

1. Place the programming overlay on any M7310 or M7324

telephone.

2. Press

ƒ••¤flfl‹›› (CONFIG).

The display shows

Password:

3. Press

¤‹fl›fl (ADMIN). The display shows

Terminals&Sets

4. Press

‘ until the display shows

System

prgrming

5. Press

≠. The display shows

Hunt groups

6. Press

≠. The display shows

Show group

7. Enter the Hunt Group number you want to program (1-6).

8. Press

≠. The display shows

Member DNs:

9. Press

‘ until the display shows

Mode

10. Press

CHANGE

to set the mode:

Sequential

Rotary

Broadcast

11. Press

® to exit or ‘ to continue programming.

Setting the hunt delay

This setting allows you to program the number of rings the
system permits at a Hunt Group set before moving on to the
next set in the Hunt Group.

1. Place the programming overlay on any M7310 or M7324

telephone.

2. Press

ƒ••¤flfl‹›› (CONFIG).

The display shows

Password:

p0881596.book Page 153 Wednesday, November 18, 1998 4:50 PM

Summary of Contents for Compact ICS 4.0































































































































































































































































Search results

Summary of Contents for Compact ICS 4.0

Reviews:

Related manuals for Compact ICS 4.0

Brands by name

Popular brands

Northern Telecom Compact ICS 4.0, Manual

Search results

Summary of Contents for Compact ICS 4.0

Reviews:

Related manuals for Compact ICS 4.0

Brands by name

Popular brands