Northern Telecom Compact ICS 4.0 Manual Download Page 162

Page: 162 / 254

150 / Programming Hunt Groups

Compact ICS 4.0 System Coordinator Guide

P0881596 Issue 02

10. Press

ADD

to add a member or press

REMOVE

to remove a

member from the group.

11. Press

® to exit or ‘ to continue programming.

Moving members of a group

Member order within a Hunt Group is important. The member
order determines how a call is routed through a Hunt Group.

1. Place the programming overlay on any M7310 or M7324

telephone.

2. Press

ƒ••¤flfl‹›› (CONFIG).

The display shows

Password:

3. Press

¤‹fl›fl (ADMIN). The display shows

Terminals&Sets

4. Press

‘ until the display shows

System

prgrming

5. Press

≠. The display shows

Hunt groups

6. Press

≠. The display shows

Show group

7. Enter the Hunt Group number you want to program (1-6).

8. Press

≠. The display shows

Member DNs:

9. Press

≠. The display shows the members for that

group.

10. Press

MOVE

to move an existing member to another place

within the Hunt Group. The display shows the member
number followed by an arrow.

11. Enter the new position number for the extension.

12. Press

® to exit or ‘ to continue programming.

p0881596.book Page 150 Wednesday, November 18, 1998 4:50 PM

Summary of Contents for Compact ICS 4.0































































































































































































































































Search results

Summary of Contents for Compact ICS 4.0

Reviews:

Related manuals for Compact ICS 4.0

Brands by name

Popular brands

Northern Telecom Compact ICS 4.0, Manual

Search results

Summary of Contents for Compact ICS 4.0

Reviews:

Related manuals for Compact ICS 4.0

Brands by name

Popular brands