North KLASIK Series Operating Manual Download Page 2 | Manualshive

Page: 2 / 40

background image

Read and understand this entire Manual and your employer’s safety practices

before installing, oper-

ating, or servicing this Product. While the information contained in this Manual represents the Manu-

facturer’s best judgment, the Manufacturer assumes no liability for its use

User Manual No: OM-10

4

A EN

for: KLASIK Spool and Push-Pull MIG/MAG Manual Welding Torches

KLASIK

Spool and Push-Pull

MIG/MAG Manual Welding Torch

Model Number

Spool Torch

QLBF-200 III-6E, QLBF-200 III-8E, QLBF-200 III-6T, QLBF-200 III-8T; QLBF-185-6, QLBF-185-8.
QTLB-24D-SP-6E, QTLB-24D-SP-8E, QTLB-24D-SP-6T, QTLB-24D-SP-8T.
QTLB-36D-SP-6E, QTLB-36D-SP-8E, QTLB-36D-SP-6T, QTLB-36D-SP-8T.

Push-Pull

Torch

PG4000-6, PG4045-6, PG4000-8, PG4045-8; PW5000-6, PW5045-6, PW5000-8, PW5045-8.
QTLB-24D-6, QTLB-24D-6, QTLB-24D-8, QTLB-24D-8; QTLB-36D-6, QTLB-36D-6, QTLB-36D-8, QTLB-36D-8.

Published by:

Jinan North Welding Tools Co Ltd
The North of 308 National Highway, Daqiao Town,
Tianqiao Zone, Jinan 250121, Shandong, China.

Website:

www.northweld.com

Copyright © 2018 by: Jinan North Welding Tools Co. Ltd.

® All rights reserved.

Reproduction of this User Manual, in whole or in part, without written permission of the publisher is prohibited.

The publisher does not assume and hereby disclaims any liability to any party for any loss or damage caused by
any error or omission in this User Manual, whether such error results from negligence, accident, or any other
cause.

Publication Date: May 2022

Record the following information for Warranty purposes

Place of Purchase:

Purchase Date:

«
1
2
3
4
...
»

Summary of Contents for KLASIK Series









































Reviews:

No comments

Related manuals for KLASIK Series

Brand: hager Pages: 10

Brand: Paradox Pages: 2

Digiplex EVO DGP2-640

Brand: Paradox Pages: 24

Brand: quadient Pages: 10

Brand: LaserLine Pages: 68

Brand: RTRMAX Pages: 14

Brand: Black Widow Security Pages: 6

KegMaster 4 Series

Brand: Keg King Pages: 17

Brand: T.L. FAHRINGER Pages: 26

Brand: Q-See Pages: 10

Brand: jablotron Pages: 2

Brand: Beta Three Pages: 10

Brand: Orno Pages: 18

Brand: Parweld Pages: 16

Brand: Nevir Pages: 24

Brand: VENCO Pages: 52

Brand: Magnavox Pages: 12

Brand: BHM Medical Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands