North KLASIK Series Operating Manual Download Page 31

Page: 31 / 40

REPLACING WORN CONSUMABLE PARTS for PUSH-PULL TORCH

May 25, 2022

Page 31

User Manual No: OM-10

A EN

7.03

PUSH-PULL TORCH QTLB-24D / QTLB-36D: Change Pressure Roll / Drive Roll

CHANGE Drive Roll (8)

a) Disconnect Power to the MIG/MAG equipment.

b) Unscrew

Handle Nut (1)

Trigger Screw (11),

Rear Handle Screw (12)

and 3 x

Handle Screws (2)

c) Wiggle the

Handle Half (3)

away from the Torch Handle then towards

the

Cable Assembly

d) Unscrew and remove

Screw (4)

and

Washer (5)

from the

Drive Shaft.

e) Push down on the red

Pressure Roll Release Button (10)

then slide the

Drive Roll (8)

off the

Drive Shaft. Do NOT

lose the

Drive Key (9)

f) Fit a new

Drive Roll (8)

and then re-assemble the Push-Pull Torch.

Note

: Ensure the

Drive Key (9)

is fitted into the slot of the

Drive Shaft

then line up the slot in the

Drive Roll (8)

with the

Drive Key (9)

CHANGE Pressure Roll (6)

a) Disconnect Power to the MIG/MAG equipment.

b) Unscrew

Handle Nut (1)

Trigger Screw (11),

Rear Handle Screw (12)

and 3 x

Handle Screws (2)

c) Wiggle the

Handle Half (3)

away from the Torch Handle then towards

the

Cable Assembly

d) Push down on the red

Pressure Roll Release Button (10)

then unscrew

the

Screw (4)

to remove the

Washer (5),

Pressure Roll (6),

and

Bear-

ing (7)

from the

Pressure Mechanism. Do NOT

lose the

Bearing (7)

e) Fit a new

Pressure Roll (6)

and then re-assemble the Push-Pull Torch.

7.04

PUSH-PULL TORCH PG4000 / PG4045, PW5000 / PW5045: Change Pressure Roll / Pres-
sure Arm Assy

CHANGE Drive Roll (8)

a) Disconnect Power to the MIG/MAG equipment.

b) Slide the

Wire Drive Mechanism Cover (3)

towards the back of the

PUSH-PULL Torch.

c) Release the

Tension Arm (10)

off the

Hook (7)

then move the Tension

Arm away from the

Pressure Arm Assy (6)

d) Unscrew and remove

Nut (9)

then remove the

Drive Roll (8)

Do NOT

lose the

Drive Key.

e) Fit a new

Drive Roll (8)

and then re-assemble the Push-Pull Torch.

Note

: Ensure the

Drive Key

is fitted into the slot of the

Drive Shaft

then

line up the slot in the

Drive Roll (8)

with the

Drive Key

CHANGE Pressure Arm Assy (6)

a) Disconnect Power to the MIG/MAG equipment.

b) Slide the

Wire Drive Mechanism Cover (3)

towards the back of the

PUSH-PULL Torch.

c) Release the

Tension Arm (6)

off the

Hook (7)

then move the

Tension

Arm

(6)

away from the

Pressure Arm Assy (6)

d) Unscrew and remove

Screw (11)

then remove the

Pressure Arm Assy

(6)

e) Fit a new

Pressure Arm Assy (6)

and then re-assemble the Push-Pull

Torch.

Summary of Contents for KLASIK Series









































Search results

Summary of Contents for KLASIK Series

Reviews:

Related manuals for KLASIK Series

Brands by name

Popular brands

North KLASIK Series, Operating Manual

Search results

Summary of Contents for KLASIK Series

Reviews:

Related manuals for KLASIK Series

Brands by name

Popular brands