manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 74

Page 74 of 174

Configure the M3900 Series Meridian Digital Telephone

553-3001-216 Standard

5.00

January 2002

M3900 Series key descriptions

This section provides key description and key configuration information for
each model of the M3900 series. This section also shows the physical
placement of the keys on each model: M3901, M3902, M3903, M3904, and
M3905.

M3901 key descriptions

Table 8 gives a description of the keys on the M3901. Figure 7 shows the
physical placement of the keys on the M3901.

FSUM ALL

Display a complete report on all M3900 Series telephones
based on parameters specified in LD 97.

The format of the report is as follows:

TYPE: tttt CUST: cc PDN: ddddddd TN: l s c u FW: vv
Where:
tttt = 3902, 3903, 3904 or 3905
cc = 0-99
ddddddd = the Primary DN of the telephone
vv = the flash firmware version

Table 8
M3901 key description

Key Number

Description

Key 0

Line (Directory Number).

Note:

The system administrator can configure Key 0 as a Voice Call (VCC),

HotLine (HOT) Key, Single Call Non-ringing, Private Line Non-ringing, Multiple Call
Non-ringing, Private Line Ringing, or Multiple Call Ringing.

Key 1

Feature or Auto Dial.

Key 2

Feature or Auto Dial.

Key 3

Feature or Auto Dial.

LD 32

– Flash Download commands (Part 2 of 2)

Prompt

Response

Description

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands