manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 148

Page 148 of 174

Appendix A: Flash Download procedure

553-3001-216 Standard

5.00

January 2002

Test Core/Net 1

1

Test Call Processing. This includes, but is not limited to the following:

a.

Check for dial tone.

b.

Make internal, external, and network calls.

c.

Check attendant console activity.

d.

Check DID trunks.

e.

Check any auxiliary processors.

Note:

From this point forward you will be upgrading Core/Net 0.

Install software on Core/Net 0

1

Move the CPSI port cable from J25 on Core/Net 1 to J25 on Core/Net 0.

2

Set the IODU/C faceplate switch to ENB.

3

Place the CP Install disk that corresponds with the installed CP card type
into the IODU/C in Core/Net 0.

a.

Press the button on the CD-ROM drive to open the CD-ROM disk
holder.

b.

Place the CD-ROM disk into the holder with the disk label showing.

c.

Use the four tabs to secure the CD-ROM drive.

d.

Press the button again to close the CD-ROM disk holder (do not
push the holder in by hand).

4

Press the MAN RST button on the CP card in Core/Net 0 to reboot the
system and start the Software Installation Tool. (The terminal displays
SYSLOAD messages during file loading. When SYSLOAD is
completed, the NT logo appears.)

5

When the NT logo appears, press <CR> to continue.

6

When the Main Menu appears, select the followingoptions in sequence:

<u> to Install menu

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands