manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 144

Page 144 of 174

Appendix A: Flash Download procedure

553-3001-216 Standard

5.00

January 2002

STAT the hardware

1

Load LD 137 and get the status of the hard disks.

Note:

Be sure the hard disks are synchronized. If not, synchronize

before proceeding.

LD 137
STAT

Get the status of the hard disks

SYNC

Synchronize hard disks if necessary. Synchronization may take

up to 50 minutes

TEST CMDU

Performs hard and floppy disk test.

****

exit program

2

Load LD 135 and get status of the CPs, CNIs and memories.

LD 135

STAT CPU

Get the status of both CPs and memory

STAT CNI

Get the status of all configured CNIs

3

Test the standby (inactive) CP. Then switch CPs, and test again.

TEST CPU

Test standby (inactive) CP

Wait until the terminal returns a complete test message. The message
HWI533 or HWI534 does not mean the test has completed!

SCPU

Switch CPs

TEST CPU

Test the standby (inactive) CP

Note:

Testingthe CPs can take up to 20 minutes for each test. When the

test is complete, the memories are automatically synchronized.

Split the Cores

1

Be sure CP 0 is active and CP1 is standby. You may need to switch CPs
again:

STAT CPU

****

exit program

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands