manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 166

Page 166 of 174

Appendix A: Flash Download procedure

553-3001-216 Standard

5.00

January 2002

Commands for System wide Flash Download of M3900 sets

LD 97

– Configure parameters for System-wide Flash Download.

Prompt

Response

Description

REQ

CHG
PRT

Change Flash Download parameters.
Print Flash Download parameters.

TYPE

FDL

Flash Download for M3900 sets.

FDTP

3902
3903
3904
3905
ALL
(NONE)

Enter M3900 set type selected for Flash Download.
M3902 telephone
M3903 telephone
M3904 telephone
M3905 telephone
All of the above
None of the above (default)

FDTM

(NO)
YES

Time interval restriction for Flash Download.
Do not change time intervals (default).
Proceed to change time intervals.

Note 1:

Flash Download is automatically paused one hour before

virtual midnight (see TODR in LD 17) to allow midnight routines to
run.

Note 2:

This option is not applicable to reporting.

FDAY

d n

Enter day and number of time intervals for Flash Download,
where:
d = day of the week (0-6 for Sunday to Saturday)
n = number of time intervals (0-4)
To disallow download for the day, enter 0.
Day is re-prompted until you enter a Carriage Return,
<CR>.

Note 1:

This prompt appears only if FDTM = YES.

Note 2:

If two or more intervals are specified, they must be

overlapping, non-consecutive, and in order.

FINT

s l

Enter starting hour and length for a time interval, where:
s = starting hour (0-23)
l = length of interval in hours (1-24)

Note:

FINT is prompted

n

time if

n

is greater than 0.

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands