manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 168

Page 168 of 174

Appendix A: Flash Download procedure

553-3001-216 Standard

5.00

January 2002

LD 32

– Flash Download commands.

FRCE

(NO)

YES

System-wide Flash Download control option.
Conditional (default).
System-wide Flash Download (using the FDLS command in
LD 32) applies only to an M3900 series set whose flash
firmware version is different is different from the version
currently found on the system disk.

Forced.
Force System-wide Flash Download to all of the specified
M3900 series sets regardless of their current flash firmware
versions.

Note 1:

Use this option with caution.Once the download tree is

built (that is, after executing FDLS in LD 32), this option
automatically reverts to NO.

Note 2:

This option is not applicable to reporting.

FVER

v

Flash firmware version specified for full report, where:
v = Flash firmware version (0-99)
If 0, report all versions (default).

Note:

This option is applicable to reporting only (through the

FSUM ALL command in LD 32).

Prompt

Response

Description

.

FDLU l s c u

Initiate conditional download to one telephone.
Terminal number, where:
l = loop address
s = shelf address
c = card address
u = unit address

.

FDLI l s c u

Initiate conditional download to an M3900 Series telephone
when it becomes idle.

.

FDLF l s c u

Initiate a forced download to an M3900 Series telephone
regardless of its version and state.

.

FWVU l s c u

Query and print the firmware versions currently on an
M3900 Series telephone.

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands