manualshive.com logo in svg

Nortel M3905, Installation And Administration Manual

Share
Download
Nortel M3905 Installation And Administration Manual Download Page 130

Page 130 of 174

Appendix A: Flash Download procedure

553-3001-216 Standard

5.00

January 2002

Overlay 32

To use the Flash Download capability, load Overlay 32 and issue the
followingcommands:

FSTN

l s c u
c u

Starting terminal number for Flash Download.
Prompt appears only if FTNR = YES.

FETN

l s c u
c u

Ending terminal number for Flash Download.
Prompt appears only if FTNR = YES.

FDNR

(NO)
YES

DN range restriction option for Flash Download.
No DN restriction (default).
Specify DN range.

FDDN

c d1 d2
<CR>

Flash Download Prime Directory Number range.
Prompt appears only if FDNR = YES.
c = Customer number (0-99)
d1 = starting Prime DN
d2 = ending Prime DN

FRCE

(NO)

YES

System-wide Flash Download control option
Conditional (default).System-wide Flash Download
(through FDLS in LD 32) applies only to an M3900 series
set whose flash firmware version is different from the
version currently found on the system disk.
Forced System-wide Flash Download to all specified M3900
series sets regardless of their current flash firmware
versions.

Note 1:

Use this option with caution! Once the download tree is

built (i.e., after executing FDLS in LD 32), this option automatically
reverts to NO.

Note 2:

This option is not applicable to reporting.

FVER

v

Flash firmware version specified for full report.
v = Flash firmware version (0-99)
If 0, report all versions (default).

Note:

This option is applicable to reporting only (through FSUM

ALL in LD 32).

Summary of Contents for M3905

















































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands