background image

Determining the minimum number of DC power supplies

35

Table 2
DC power supply shipping accessories: 8004DC (cont’d.)

Check

Accessory

Purpose

5 nuts

Connect all leads.

5 lock washers

Connect all leads.

1 washer

Connect the ground
stud.

Use

Table 3 "DC power supply shipping accessories: 8005DC" (page

35)

as a checklist to verify the contents of the 8005DC shipping container.

Table 3
DC power supply shipping accessories: 8005DC

Check

Accessory

Purpose

3 two-hole crimp
lug terminals with
attached tubing

Connect the
positive and
negative power
inputs.

6 nuts

Connect all leads.

6 lock washers

Connect all leads.

2 washers

Connect the
ground stud.

Determining the minimum number of DC power supplies

Use the following procedure to determine the minimum number of power
supplies to install for the Ethernet Routing Switch 8600 system:

For more information, see Nortel Ethernet Routing Switch 8600 Installation
— Chassis 
(NN46205-303) .

Procedure steps

Step

Action

1

Add the total (3.3 V and 12 V) input power consumption
(wattage) for all components (modules and fan trays or cooling
modules).

2

Refer to the output power rating of the 8005DC power supply
based on the input connection.

If either the individual or the combined power requirements for
the components exceed the power supply rating, you need to
add at least another power supply to your configuration.

Nortel Ethernet Routing Switch 8600

Installation — DC Power Supply

NN46205-307

02.02

19 December 2008

Copyright © 2008 Nortel Networks

.

Summary of Contents for 8004DC







































































Reviews: