manualshive.com logo in svg

Nordson Asymtek Spectrum S-920, Installation, Operation & Maintenance Manual

Share
Download
Nordson Asymtek Spectrum S-920 Installation, Operation & Maintenance Manual Download Page 51

Installation  

3-1 

3 Installation 

3.1 Overview 

This section describes installation procedures for the Spectrum Series S-920 Dispensing System and 
covers the following topics:   

•

 

Uncrating and Placing the Dispensing System 

•

 

Unpacking the Dispensing Chamber 

•

 

Leveling the Dispensing System 

•

 

Leveling the Scale 

•

 

Setting Up the Service Station 

•

 

Installing the Light Beacon 

•

 

Installing the Laptop Computer 

•

 

Installing the Camera 

•

 

Anchoring the Dispensing System 

3.2 Safety 

First 

Operation of your S-920 Dispensing System involves heat, air pressure, electrical power, mechanical 
devices, and the use of hazardous materials. It is essential that every person servicing or operating the 
dispensing system fully understands all hazards, risks, and safety precautions. Refer to 

Section 2 - Safety 

for additional information. 

 

CAUTION!

 

Installation procedures should only be performed by a trained service technician. 

3.3 Facility 

Requirements 

To ensure optimal performance and safety, it is necessary to install the dispensing system in a facility that 
meets the requirements. If you have any questions about facility requirements, please contact Asymtek 
Technical Support. See 

10.2 Facility Requirements

 for detailed information. 

3.4 

Tools and Materials Needed 

•

 

3 mm hex key 

•

 

1/2-inch wrench 

•

 

9/16-inch wrench 

•

 

Phillips Screwdriver (included in tool kit) 

•

 

Band Cutter 

•

 

1 ½-inch wrench (included in tool kit) 

•

 

Personal Protective Equipment 

•

 

Diagonal-cut pliers 

•

 

Hammer 

•

 

Forklift 

•

 

Flat Bar 

•

 

Box Level 

Summary of Contents for Asymtek Spectrum S-920















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands