background image

OPERATION

Falcon

t

Ultra B (07--05)

4

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is

designed exclusively to clean carpets and

upholstery in an indoor environment and is not

constructed for any other use. Use only

recommended accessory tools and commercially

available carpet cleaners intended for machine

application.
All operators must read, understand and practice

the following safety precautions.

The following warning alert symbol and the “FOR

SAFETY” heading are used throughout this manual as

indicated in their description:

WARNING: To warn of hazards or unsafe

practices which could result in severe personal

injury or death.
FOR SAFETY: To identify actions which must be

followed for safe operation of equipment.

Failure to follow these warnings may result in

personal injury, electrical shock, fire or explosion.

WARNING: Fire Or Explosion Hazard:

--

Never Use Flammable Liquids Or Operate

Machine in Or Near Flammable Liquids,

Vapors Or Combustible Dusts.

This machine is not equipped with explosion proof

motors. The electric motors will spark upon start

up and during operation which could cause a flash

fire or explosion if machine is used in an area

where flammable vapors/liquids or combustible

dusts are present.

--

Do Not Pick Up Flammable Materials Or

Reactive Metals.

--

Batteries Emit Hydrogen Gas. Keep Sparks

And Open Flame Away. Keep Battery

Compartment Open When Charging.

WARNING: Electrical Shock Hazard.

Disconnect Battery Cables Before Servicing

Machine.

WARNING: Spinning Brush. Keep Hands

Away. Turn Off Power Before Working On

Machine.

The following information signals potentially

dangerous conditions to the operator or

equipment:
FOR SAFETY:
1. Do not operate machine:

--

With flammable liquids or near flammable

vapors as an explosion or flash fire may

occur.

--

Unless trained and authorized.

--

Unless operation manual is read and

understood.

--

If not in proper operating condition.

2. Before operating machine:

--

Make sure all safety devices are in place

and operate properly.

--

Place wet floor signs as needed.

3. When using machine:

--

Go slow on inclines and slippery surfaces.

--

Use care when reversing machine.

--

Report machine damage or faulty

operation immediately.

--

Never allow children to play on or around.

--

Follow mixing and handling instructions

on chemical containers.

4. Before leaving or servicing machine:

--

Stop on level surface.

--

Turn off machine.

--

Set parking brake, if equipped.

5. When servicing machine:

--

Avoid moving parts. Do not wear loose

jackets, shirts, or sleeves.

--

Disconnect battery connections before

working on machine.

--

Wear protective gloves and eye protection

when handling batteries or battery cables.

--

Avoid contact with battery acid.

--

Block machine tires before jacking up.

--

Use hoist or jack that will support the

weight of the machine.

--

Do not power spray or hose off machine.

Electrical malfunction may occur.

--

Use manufacturer supplied or approved

replacement parts.

--

All repairs must be performed by a

qualified service person.

--

Do not modify the machine from its

original design.

Summary of Contents for FALCON ULTRA B















































Reviews: