background image

FORM NO. 56043097 / Adgressor

 / BR 850S, 850CS, 950S, 950CS, 1050S, 1050CS - 71

ELECTRICAL SYSTEM

Back-up Alarm Volume Control:
FACTORY DEFAULT: 0 (OFF)
The Adgressor/BR 850S and BR850CS are equipped with an audible warning device which functions as a horn, a back-up alarm, and a forward 
annunciator.  The volume of the back-up alarm can be adjusted to one of ten settings.  1 is the minimum setting and 9 is the maximum setting, 0 is 
off.  To change the back-up alarm volume perform the following steps:
1  Turn the main power key switch to the off position.
2  Press and hold the horn switch.
3  While holding the horn switch turn the main power key switch to the on position.
4  Continue to hold the horn switch until the red battery status indicator is lit and the status display shows a number from 0 to 9 depending on the 

current volume setting.

5  Release the horn switch.
6  Pressing and releasing the horn switch will now select the volume level.  The level will increment from 0 to 9, 9 being the loudest.  To hear the 

back-up alarm volume select the reverse direction by pressing lightly on the throttle.

7  To save the new setting turn the main power key switch to the off position.
8  The new setting will be saved and will remain in effect until it is changed again.

Forward Annunciator Volume Control:
FACTORY DEFAULT: 0 (OFF)
The Adgressor/BR 850S and 850CS are equipped with an audible warning device which functions as a horn, a back-up alarm, and a forward 
annunciator.  The volume of the forward annunciator can be adjusted to one of ten settings.  1 is the minimum setting and 9 is the maximum setting, 
0 is off.  To change the forward annunciator volume perform the following steps:
1  Turn the main power key switch to the off position.
2  Press and hold the scrub system off and the horn switch.
3  While holding both switches turn the main power key switch to the on position.
4  Continue to hold both switches until the green battery status indicator is lit and the status display shows a number from 0 to 9 depending on the 

current volume setting.

5  Release the horn switch.
6  Pressing and releasing the horn switch will now select the volume level.  The level will increment from 0 to 9, 9 being the loudest.  To hear the 

forward annunciator volume select the forward direction by pressing lightly on the throttle.

7  To save the new setting, turn the main power key switch to the off position.
8  The new setting will be saved and will remain in effect until it is changed again.

SPECIAL PROGRAM OPTIONS (CONTINUED)

Summary of Contents for Adgressor BR 1050CS



















































































Reviews: