FORM NO. 56043097 / Adgressor
™
/ BR 850S, 850CS, 950S, 950CS, 1050S, 1050CS - 11
FUNCTIONAL DESCRIPTION OF CONTROL BUTTONS:
The controls on the Adgressor – BR850s and BR850CS were designed with one touch operation in mind. For single pass scrubbing the user can
simply depress one switch and all systems on the machine will be ready to go.
For most single-pass scrubbing operations, the operator should only need to use the top three switches on the control panel. These are the Scrub
System Off, Scrub Pressure Decrease, and Scrub Pressure Increase switches.
The scrub system switches can be programmed to operate three different ways. The fi rst method of operation described below is the factory default
setting. See the programming section for details.
Pressure Increase / Decrease Mode (Factory Default)
Scrub Off Switch (B) – Pressing this switch when the unit is in a scrub mode will cause the following to occur:
•
The scrub brushes will turn off and the scrub deck will raise to the up position
• The
solution
fl ow will be stopped
• The
fi rst time that this switch is pressed, the vacuum/squeegee system will NOT be turned off. This is so that any remaining water may be
picked up without having to turn the vacuum back on. If this switch is pressed a second time (pressed after the scrub system has been turned
off) the squeegee will raise and the vacuum will shut of after a 10 second delay.
•
The travel speed limit will return to the transport speed setting
•
The scrub off indicator will be green if the scrub system is off and ready to be activated. The indicator will be off if the scrub system has been
activated. If the scrub system has been turned off and the scrub deck is not up yet, or if the scrub deck is up and there is no weight on the seat,
the indicator will be red. If there is a fault in the scrub system this indicator will fl ash red.
Scrub Pressure Decrease Switch (D) – If the scrub system is off, pressing this switch will cause the following to occur:
•
The scrub system will be enabled with the scrub pressure set to the last used setting and the scrub deck will be lowered
•
The vacuum system will be enabled and the squeegee will be lowered
•
The solution system will be enabled
•
The travel speed will be limited to the scrub speed setting
•
As soon as the throttle is moved from the neutral position the scrub brushes will start turning and the vacuum will turn on. If the direction is
forward the solution fl ow will start. If the direction is reverse, the squeegee will raise and the solution fl ow will be stopped.
•
The scrub pressure decrease indicator will be green if the scrub system is on and the pressure is set at 1 or 2. The indicator will be off if the
scrub system is off or if the scrub pressure is set to maximum. The indicator will be yellow if the scrub system has been enabled but the throttle
is in neutral.
Scrub Pressure Increase Switch (F) – If the scrub system is off, pressing this switch will cause the following to occur:
•
The scrub system will be enabled with the scrub pressure set to the last used setting and the scrub deck will be lowered
•
The vacuum system will be enabled and the squeegee will be lowered
•
The solution system will be enabled
•
The travel speed will be limited to the scrub speed setting
•
As soon as the throttle is moved from the neutral position the scrub brushes will start turning and the vacuum will turn on. If the direction is
forward the solution fl ow will start. If the direction is reverse, the squeegee will raise and the solution fl ow will be stopped.
•
The scrub pressure increase indicator will be green if the scrub system is on and the pressure is set at 2 or 3. The indicator will be off if the
scrub system is off or if the scrub pressure is set to minimum. The indicator will be yellow if the scrub system has been enabled but the throttle
is in neutral.
KNOW YOUR MACHINE
Summary of Contents for Adgressor BR 1050CS
Page 81: ......
Page 82: ...www nilfisk advance com 2006 ...
