Nikon NPL-632 Instruction Manual Download Page 95

Page: 95 / 206

Field Station NPL-632 Instruction Manual

Applications

The distance from the station point to the first
point appears.

Sight the second point and press

[MSR1]

[MSR2]

The distances between the first and second point
are displayed

To change display screens, press

[DSP]

To record the distance and angle information as
a comment record, press

[ENT]

in the 1/2 or 2/2

observation screen.

Default point numbers are displayed. You can
change these point numbers. To record a note,
press

[ENT]

in the To field.

rSD

Slope distance between two points

rVD

rVD Vertical distance between two points

rHD

rHD Horizontal distance between two
points

rAZ

Azimuth from first point to second point

rV%

Percentage of grade (rVD/rHD) × 100%

rGD

rGD Vertical grade (rHD/rVD): 1

Data that you save in RDM functions is stored in RM records. For more information, see

RM records, page 123

When you download data in Nikon RAW format, they are output as comment (CO) records.

Summary of Contents for NPL-632















































































































































































































Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands

Nikon NPL-632, Instruction Manual

Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands