Nikon NPL-632 Instruction Manual Download Page 90

Page: 90 / 206

Applications

Field Station NPL-632 Instruction Manual

Program Key

To display the Programs menu, press

[PRG]

Measuring distance and offset values along a specified line

Press

[1]

or select

2Pt RefLine

in the

Programs menu.

Enter the first point for the reference line.
Alternatively (to enter the point by measuring),
press the

MsrPT

softkey.

Enter the second point for the reference line.

Enter an asterisk (*) in the PT field to perform a
wildcard search. A list of matching points
appears. Highlight a point in the list and then
press

[ENT]

Direct Measurement screen

•

Press the

MsrPT

softkey to display a direct measurement screen.

•

Sight the target and then press

[MSR1]

[MSR2]

. The Record PT screen

appears.

•

If you press

[ESC]

in the Record PT screen, the measured point is used but

not recorded in the job.

Plain view

Side view

PT1

PT2

Sta

O/S

Prism

PT2

Sta

PT1

Summary of Contents for NPL-632















































































































































































































Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands

Nikon NPL-632, Instruction Manual

Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands