Nikon NPL-632 Instruction Manual Download Page 108

Page: 108 / 206

Applications

Field Station NPL-632 Instruction Manual

Measuring circle offsets

To enter the circle center calculation function,
press

[7]

or select

Circle

in the Offset menu.

If you have not taken a measurement to the
circle before entering this function, a temporary
measurement screen appears.

Sight any point on the surface of the circle and
then press

[MSR1]

[MSR2]

Sight one edge of the circle and then press

[ENT]

Sight the other edge of the circle and then press

[ENT]

The instrument calculates and records the center
of the circle.

It also calculates the coordinates of the center
point and the radius of the circle.

To record the point, press

[ENT]

or the

softkey.

If you use a prism attached to the surface of the circle for the distance measurement, press the

+SD

softkey to

eliminate the offset error (from the attached point to the measured surface of the prism) before you press

[ENT]

If you have taken a distance measurement to the center of the circle, press the

Calc

softkey to calculate the

offset using one edge angle observation.

Summary of Contents for NPL-632















































































































































































































Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands

Nikon NPL-632, Instruction Manual

Search results

Summary of Contents for NPL-632

Reviews:

Related manuals for NPL-632

Brands by name

Popular brands