manualshive.com logo in svg

NIKKARI SSBC, Instruction Manual

Share
Download
NIKKARI SSBC Instruction Manual Download Page 44

44

October , 2012 

E1381-0

Manufacturer   NIKKARI CO.,LTD.

 

Address           465-1,Saidaiji-Kawaguchi,Higashi-ku,Okayama,704-8125
Country           JAPAN

Type                Brush Cutter Attachment 
Model              SSBC
Serial No.        SBCE-1000001 ~

Declare, that the following machinery complies with all the essential health and safety 
Requirements of the EC Directive.
  2006/42/EC
  2004/108/EC
  2000/14/EC amended 2005/88/EC

The following standards have been applied 
  EN ISO 12100:2010
  EN ISO 11806-1:2011
  EN ISO 14982:2009

Approved Powerhead  
  UMC425E
  UMC435E

Guaranted sound power level (in accordance with 2000/14/EC)
  Use with UMC425E       112 dB(A)
  Use with UMC435E       111 dB(A)

Issued at: Hiroshi Sugimoto, Japan
on October 1st 2012
Name and position of the person that signs: Hiroshi Sugimoto
President
Manufacturer’ s signature

Person authorised to complie the technical file 
  Honda Motor Europe Ltd.  Aalst Office
  Wijngaardveld 1 (Noord V), 9300 Aalst
  BELGIUM

EC Declaration of Conformity

( Applies to Europe only )

Summary of Contents for SSBC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands