manualshive.com logo in svg

NIKKARI SSBC, Instruction Manual

Share
Download
NIKKARI SSBC Instruction Manual Download Page 31

31

4.7  Actions after Operation

After using the brush cutter, take the following actions.

Set the start/stop switch to OFF (O side) to stop the engine.

Tighten all the nuts, bolts, and screws other than the ones for adjusting the 
carburetor.

Store the brush cutter according to “6. Storing”.

5. Maintenance

Before performing maintenance, repair or cleaning, stop the engine and remove 
the attachment from the powerhead. 

*  If the engine starts during the work, hands or fingers could be severed by the moving 

parts or cutting part.

Do not perform any maintenance or repair other than those described in the 
instruction manual. Request the sales agency.

*  It could cause an accident.

Maintenance items for the attachment are described as follows.
For maintenance of the powerhead, refer to the powerhead manual.

■ Maintenance List

Item

Daily

Every 20 hours 

or 3 months

As necessary

Remarks

Inspection of cutting part

○

Refer to 5.1.1

Looseness of screws and nuts

○

Refer to 5.1.2

Removal of foreign objects

○

Refer to 5.1.3

Greasing

○

Refer to 5.2.1

Replacement of nylon line

○

Refer to 5.3.1

1
2

3

Summary of Contents for SSBC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands