manualshive.com logo in svg

NIKKARI SSBC, Instruction Manual

Share
Download
NIKKARI SSBC Instruction Manual Download Page 2

2

Important Information

Intended Purpose

This product (hereinafter referred to as an attachment) is designed to be attached to the powerhead (to 
be purchased separately) for cutting grasses, weeds and bushes. The brush cutter is attached to our 
approved powerhead.  
Do not use the brush cutter for any other purpose or in any other way.

Brush cutter

Powerhead (Separately sold)

Attachment

Attachment 
(This product)

General

 

● This attachment is equipped with the nylon cutter as a standard item. 

It is also possible to use the nylon cutter attached  to the iron blade (option).

 

● When using the iron blade (option),  use a genuine blade kit (designed to be used in Australia) or 

genuine parts. Before using the iron blade designed to be used in Australia, read the manual of the 
blade kit designed to be used in Austraia carefully and have a good understanding of the contents. 

 

● In this instruction manual, the word "cutting parts" is used as a general term of blades such as nylon 

cutters and iron blades (option). When describing the contents specific to the iron blade (option), the 
word "iron blade (option)" is used to identification.

 

● Refer to the powerhead manual for further information on handling the powerhead.

 

● When handling the brush cutter, observe all the applicable safety rules, standards or regulations in the 

area where the brush cutter is used.  
This brush cutter is designed and produced according to the standards and regulations applied in the 
purchase country, assuming that the use is limited to the  purchase country only. It will not comply with 
standards and regulations of other countries. Do not export or resell the brush cutters to any other 
countries because the languages are different.

 

● Before use, read this instruction manual and the powerhead manual thoroughly, and have a good 

understanding of the contents. Do not allow any person who does not understand the contents of this 
manual to handle this brush cutter.

Summary of Contents for SSBC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands