manualshive.com logo in svg

NIKKARI SSBC, Instruction Manual

Share
Download
NIKKARI SSBC Instruction Manual Download Page 39

39

8.  Installation of Iron Blade (Option)

The following shows the installation procedure for the iron blade (option).

Note

 

● Iron blades, blade caps, nut covers and nuts are separately sold.  For puchasing, contact the sales 

agency.

 

● Be sure to use genuine parts.

 

● For installation of iron blade designed to be used in Australia,  refer to the manual of the blade kit 

designed to be used in Australia.

Stop the engine, and pull out the brush 
cutter attachment from the powerhead.

Put on gloves.

Remove the nylon cutter [1].

                 

Loosen the fixed screw for nylon cutter 
guard [2], and remove the nylon cutter 
guard [3] from the blade guard [4].

Note

 

● The fixed screw for nylon cutter guard [2] cannot be 

removed from the nylon cutter guard [3].

 

● Store the removed nylon cutter guard [3] carefully.

 

● Do not remove the fixed screw [5] for blade guard .

1

[1]

2

3

[2]

[3]

[5]

[4]

4

Summary of Contents for SSBC













































Reviews:

No comments

Brands by name

Popular brands

Load more brands