NIKKARI SSBC Instruction Manual Download Page 12

12

1.2.9 Precautions for Storing

When storing the attachment with the hook of the pipe cap attached to the pipe, 
etc., do not pull or swing the attachment.

Or, attach it to the fixed bar having enough strength.

*  Otherwise, it will fall off, causing a serious injury.

For iron blade (option), when storing the attachment, install the transportation 
guard (option) to the iron blade (option).

*  Otherwise, it could cause injury to an operator due to contact with the iron blade (option), 

or even serious injury by getting contact with the iron blade (option) while the operator is 
falling down or tumbling.

When storing the attachment, store it in the place out of reach of children and 
animals.

*  Otherwise, it could cause injury to an operator due to contact with the iron blade (option), 

or even serious injury by getting contact with the iron blade (option) while the operator is 
falling down or tumbling.

1.2.10  Precautions for Grease

Store the grease in a place out of reach of children. 

Also, put them in a container so that the grease is not spilled and make them 
distinguished to understand contents.

*  When drinking them by mistake, the person will feel physically sick.

Do not discard grease into the river, the sea, or the ground.

*  Otherwise, it could pollute the environment.

Summary of Contents for SSBC













































Reviews: