manualshive.com logo in svg

Nice SlideSmart CNX 15, Installation And Programming Manual, Page: 2 / 48

Share
Download
Nice SlideSmart CNX 15 Installation And Programming Manual Download Page 2

2      

www.hysecurity.com

SLIDESMART CNX 15 BASIC MANUAL

MX4779 REV. A     ©2019

TABLE OF CONTENTS

SlideSmart CNX 15

Troubleshooting/Alerts/Faults/Errors .. 35-41

Appendix A - Vehicle Detector Loops .......42

Appendix B - French Translations ........ 43-46

Warranty ....................................................47

Specifications

 ............................................48

Table of Contents ........................................2

Safety Requirements .............................. 3-10

Features .....................................................11

Unpack the Operator .................................12

Operator Position ......................................13

Prepare an Installation Site .................. 14-15

Attach Back Cover .....................................16

Install Chain Kit ..........................................17

Attach Target Magnet and Chain Cover ....18

Wiring and Power ................................ 19-20

Controller Connections .............................21

User Interface ............................................22

Initial Setup ................................................23

Operator Configurations

 ...........................24

Bi-Parting Gate Setup ................................25

Controller Inputs ........................................26

Set IES Sensitivity ......................................27

Entrapment Sensor Wiring - BlueBUS .......28

Entrapment Sensor Wiring ........................29

List of Entrapment Sensors ........................30

SmartCNX - Hy5B Module ........................31

Relay Outputs - Basic ................................32

Maintenance ..............................................33

Firmware Updates and Debug Data ..........34

Visit https://hysecurity.com/contact-us/technical-
support/ for Installation manuals, replacement part 
instructions, part diagrams and more.

The Advanced Manual is available in digital 
form at the link above and physical copies from 
distributors. It includes additional information 
about the SlideSmart CNX. For example, the 
SmartCNX installer app, menu options, installation 

configurations, solar installations, I/O expansion 

board, external entrapment sensors, loop detectors, 
maintenance, and more.

Summary of Contents for SlideSmart CNX 15

















































Reviews:

No comments