Nice SlideSmart CNX 15, Installation And Programming Manual, Page: 28 / 48

28 www.hysecurity.com SLIDESMART CNX 15 BASIC MANUAL MX4779 REV. A ©2019
ENTRAPMENT SENSOR WIRING - BLUEBUS
Example jumper position
Close P1 Jumper storage
TX RX
NOTE: Matching wire polarity is not required for BlueBUS photocells.
NOTE: Jumper locations shown here are for a CLOSE P1 installation.
EXTERNAL
COMMUNICATIONS
NETWORK SETUP
MENU
HySecurity Gate
GATENAME
DHCP
10.3.3.2
IPV4 ADDRESS
XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4
XX.X.X.X
^
10.3.3.2
GATEWAY IPV4
XX.X.X.X
^
8.8.8.8
DNS 1 IPV4
XX.X.X.X
^
8.8.4.4
DNS 2 IPV4
XX.X.X.X
^
fec0::2
IPV6 ADDRESS
XXXX::X
^
fec0::1
IPV6 ADDRESS
XXXX::X
^
2001::4860:4860::
DNS 1 IPV6
XXXX::X
^
2001::4860:4860::
DNS 2 IPV6
XXXX::X
^
0 (OFF)
1 (ON)
RESET DEFAULTS
0 (NO)
1 (YES)
64
SUBNETLEN IPV6
1-128
SUBNETLEN IPV6
0 (OFF)
1 (ON)
USB
OPTIONS MENU
SAVE LOG
LOAD SW
CAPTURE DEBUG
0 (OFF)
1 (ON)
0 (NO)
1 (YES)
BLE
OPTIONS MENU
BLE ENABLE
BLUEBUS
OPTIONS MENU
SCAN FOR DEVICES
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
0 (OFF)
1 (ON)
NONE
BLUEBUS DEVICES
0 (NO)
1 (YES)
Placeholder for hidden OXI menu
EXTERNAL
COMMUNICATIONS
NETWORK SETUP
MENU
HySecurity Gate
GATENAME
DHCP
10.3.3.2
IPV4 ADDRESS
XX.X.X.X
^
HySecurity Gate
^
255.255.255.0
NETMASK IPV4
XX.X.X.X
^
10.3.3.2
GATEWAY IPV4
XX.X.X.X
^
8.8.8.8
DNS 1 IPV4
XX.X.X.X
^
8.8.4.4
DNS 2 IPV4
XX.X.X.X
^
fec0::2
IPV6 ADDRESS
XXXX::X
^
fec0::1
IPV6 ADDRESS
XXXX::X
^
2001::4860:4860::
DNS 1 IPV6
XXXX::X
^
2001::4860:4860::
DNS 2 IPV6
XXXX::X
^
0 (OFF)
1 (ON)
RESET DEFAULTS 0 (NO)
1 (YES)
64
SUBNETLEN IPV6
1-128
SUBNETLEN IPV6
0 (OFF)
1 (ON)
USB
OPTIONS MENU
SAVE LOG
LOAD SW
CAPTURE DEBUG 0 (OFF)
1 (ON)
0 (NO)
1 (YES)
BLE
OPTIONS MENU
BLE ENABLE
BLUEBUS
OPTIONS MENU
SCAN FOR DEVICES
SYSTEM ADDRESS 0 (OFF) - 99 (DEBUG OUT)
0 (OFF)
1 (ON)
NONE
BLUEBUS DEVICES
0 (NO)
1 (YES)
Placeholder for hidden OXI menu
†
Direction Pair
Jumper Positions
(Pairs must match)
BlueBUS
Photo Eye
Position
CLOSE P1 FOTO
OPEN P5 FOTO 2
†
= Indicates default
ENTRAPMENT
SENSOR RESPONSE
PHOTO EYE ALIGN 0 (OFF)
1 (ON)
GATE EDGE LOGIC 0 FULL OPEN
1 REVERSE 2S
EYE CLOSE LOGIC 0 STOP ONLY
1 REVERSE 2S
2 FULL OPEN
EYE OPEN LOGIC 0 STOP ONLY
1 REVERSE 2S
IES STOP ONLY 0 (OFF)
1 (ON)
REVERSAL LOGIC 0 FULL OPEN
1 REVERSE 2S
IES SENSITIVITY 0 (MAXIMUM) - 9
(2 † )
†
†
†
†
†
†
HySecurity provides one BlueBUS thru beam photo eye
pair typically used as EYE CLOSE
Install a BlueBUS photo eye:
1.
Verify the jumpers on transmitter (TX) and receiver
(RX) are in the same positions (Figure 30).
2.
Install the BlueBUS photo eyes in appropriate
locations for entrapment protection (page 9).
3.
Set the AC and DC switches to OFF.
4.
Route the wires to the inside of the CNX chassis
(Figure 7).
5.
Install the wires between the TX and RX and then
into BlueBUS terminals on the SmartCNX controller
(Figure 31).
Note: With BlueBUS technology there are 4 total close
direction pairs and 2 open direction pairs available.
Refer to Advanced Manual for more information.
Pairs may either be connected in parallel to one
another or directly to the SmartCNX Controller.
6.
Set AC and DC switches to ON.
7.
In EXTERNAL COMMUNICATIONS MENU, select
BLUEBUS OPTIONS MENU, and set SCAN FOR
DEVICES to 1 (ON).
8.
Display will show EYE CLOSE BlueBUS P1.
9.
In ENTRAPMENT SENSOR RESPONSE menu, set the
desired response action for each entrapment type.
10.
Test the function of each sensor pair.
BlueBUS RX LED
Status Light Status
Off No power
3 flashes, pause, repeat Controller has not
memorized the pair
Slow flashes Good signal
Fast flashes Weak signal
Always on No signal
Figure 30. BlueBUS and Jumper Designation
Figure 31. Connect the BlueBUS Photo Eye