manualshive.com logo in svg

Nice SlideSmart CNX 15, Installation And Programming Manual, Page: 12 / 48

Share
Download
Nice SlideSmart CNX 15 Installation And Programming Manual Download Page 12

12      

www.hysecurity.com

SLIDESMART CNX 15 BASIC MANUAL

MX4779 REV. A     ©2019

UNPACK THE OPERATOR

UNPACK THE OPERATOR

1. 

Open the box and remove the front cover, chain 

cover, rear cover, edge sensor, photo eye, chain 

hardware kit, and ship with kit.

2.  Check the contents of the ship with kit:

a.  Basic Manual

b.  UL 325 required gate safety signs and zip ties

c.  DASMA gate safety literature

d.  Rear cover mounting hardware

e.  Cover keys

f.  Chain cover lock pin

g. 

Optional 208/230VAC and 24VDC voltage 

labels

3.  Lift the chassis using the lift handles.

Lift Handle

Rear Cover

Front Cover

Chain Cover

Note: You can mark the slots and conduit area on 

the plywood underneath the chassis and then 
use the plywood as an anchor hole template.

W

20 7/8”

(53 cm)

(COVER WIDTH)

L

15 3/8”

(38 cm)

(COVER DEPTH)

GENERAL OPERATOR DIMENSIONS

H

24 1/2”

(62 cm)

(OPERATOR

HEIGHT)

Summary of Contents for SlideSmart CNX 15

















































Reviews:

No comments