manualshive.com logo in svg

Nice SlideSmart CNX 15, Installation And Programming Manual, Page: 40 / 48

Share
Download
Nice SlideSmart CNX 15 Installation And Programming Manual Download Page 40

40      

www.hysecurity.com

SLIDESMART CNX 15 BASIC MANUAL

MX4779 REV. A     ©2019

Table 3. SmartCNX Controller - Troubleshooting

Display 

Condition

Description 

Alert, Error or 

Fault

Possible Causes

Solutions

ERROR 1

 

DIRECTION 
ERROR

SmartCNX 
Controller detects 
operator ran in 
wrong direction.

Limit sensor plugs switched on drive 
module.

1.  Switch limit sensor 

plugs or reset 

operator handing 

Left Hand/Right 

Hand.

2.  Press RESET to clear 

fault.

ERROR 3

 

Hy5B FAILED*

SmartCNX 
Controller detects 
communication 
error with a Hy5B 
vehicle detector.

Caused by Hy5B removal or socket 
connection integrity.

1.  Press RESET.

2.  Remove and re-

install Hy5B.

3.  Replace Hy5B, if 

needed.

ERROR 4

 

PRIMARY-
SECONDARY

 

COM

SmartCNX 
Controller detects 
a communication 
error between 
primary and 
secondary in 
a dual gate 
installation.

Several possible causes:

 

z

Primary/Secondary communication 

cable is installed incorrectly. 

 

z

Primary/Secondary not configured 

properly through Installer Menu.

 

z

Operator is not properly earth 

grounded.

 

z

Primary/Secondary communication 

cable installed in same conduit as 

high-voltage AC power.

 

z

One operator is powered off.

 

z

Different software versions between 

operators. Check software version 

currently loaded in operator by 

pressing RESET.

1.  Correct 

communication 

cable.

2.  Verify one operator 

is set as Primary and 

the other is set as 

Secondary.

3.  Install ground rod 

per NEC/NFPA 

standard.

4.  Install 

communication 

cables in a low 

voltage conduit.

5.  Ensure AC power 

is present at both 

operators and all 

power switches are 

On.

6.  Make sure both 

operators are 

running same 

software version. 

TROUBLESHOOTING/ALERTS/FAULTS/ERRORS

* Message indicates which detector the alert applies to: Exit Loop (ELD), Inside Obstruction Loop (IOLD), 
Outside Obstruction Loop (OOLD), or Center Loop (CLD).

Summary of Contents for SlideSmart CNX 15

















































Reviews:

No comments