Installation
This function enables start-up of the procedure for learning the devices connected to the Bluebus input and the HALT input of
the control unit of an automation.
Important
– To activate the device search, press “Run”.
This function enables memorisation in the control unit of the type of motor connected. Select the type of motor from the list of
those available, using keys
p
and
q
. After selecting the motor, press “
OK
” to memorise.
This function enables an automatic search of positions: the control unit automatically measures the leaf opening angles and cal-
culates the opening and deceleration positions. To activate the position search, press “
Run
”.
•
maximum closing
This function, expressed in encoder pulses, enables programming of the maximum closing position “0” (when the leaf touches
the mechanical closing stop ). To program the position, select the motor (1 or 2) using keys
t
and
u
; then use the hold-to-run
keys
p
(
open
) and
q
(
close
), to move the selected motor to the maximum closing position. Press “
OK
” to memorise.
•
maximum opening
This function, expressed in encoder pulses, enables programming of the maximum opening position “1” (when the leaf touches
the mechanical opening stop ). To program the position, select the motor (1 or 2) using keys
t
and
u
; then use the hold-to-run
keys
p
(
open
) and
q
(
close
), to move the selected motor to the maximum opening position. Press “
OK
” to memorise.
•
opening
This function, expressed in encoder pulses, enables programming of the required opening position “A” (the position in which the
leaf should stop at the end of an opening manoeuvre). To program the position, select the motor (1 or 2) using keys
t
and
u
; then
use the hold-to-run keys
p
(
open
) and
q
(
close
), to move the selected motor to the opening position. Press “
OK
” to me morise.
•
partial open 1
This function, expressed in encoder pulses, enables programming of the partial opening position “1” (the position in which the
leaf should stop at the end of an opening manoeuvre, following a Partial Open 1 command). To program the position, select the
motor (1 or 2) using keys
t
and
u
; then use the hold-to-run keys
p
(
open
) and
q
(
close
), to move the selected motor to the
partial open 1 position. Press “
OK
” to memorise.
•
partial open 2
This function, expressed in encoder pulses, enables programming of the partial opening position “2” (the position in which the
leaf should stop at the end of an opening manoeuvre, following a Partial Open 2 command). To program the position, select the
motor (1 or 2) using keys
t
and
u
; then use the hold-to-run keys
p
(
open
) and
q
(
close
), to move the selected motor to the
partial open 2 position. Press “
OK
” to memorise.
•
partial open 3
This function, expressed in encoder pulses, enables programming of the partial opening position “3” (the position in which the
leaf should stop at the end of an opening manoeuvre, following a Partial Open 3 command). To program the position, select the
mo tor (1 or 2) using keys
t
and
u
; then use the hold-to-run keys
p
(
open
) and
q
(
close
), to move the selected motor to the par-
tial open 3 position. Press “
OK
” to memorise.
•
deceleration on opening
This function, expressed in encoder pulses, enables programming of the leaf deceleration zone, during the opening manoeuvre (dis-
tance covered by the motors from the start of the deceleration phase through to the opening position). To program decelera tion,
select the motor (1 or 2) using keys
t
and
u
; then select the required value by means of keys
p
and
q
. Press “
OK
” to me morise.
•
deceleration on closing
This function, expressed in encoder pulses, enables programming of the leaf deceleration zone, during the closing manoeuvre
(distance covered by the motors from the start of the deceleration phase through to the maximum closing position “0”). To pro-
gram deceleration, select the motor (1 or 2) using keys
t
and
u
; then select the required value by means of keys
p
and
q
Press “
OK
” to memorise.
•
open offset
This function, expressed in encoder pulses, enables programming of the leaf offset on opening (space covered by leaf 2 before
leaf 1 starts opening). To program offset, select the required value by means of keys
p
and
q
. Press “
OK
” to memorise.
•
close offset
This function, expressed in encoder pulses, enables programming of the leaf offset on closing (space covered by leaf 1 before
leaf 2 starts closing). To program offset, select the required value by means of keys
p
and
q
. Press “
OK
” to memorise.
•
disable value
This parameter, expressed in encoder pulses, can be set from 0 to 255; the factory setting depends on the type of installation.
The selected value defines the range, according to the mechanical closing and opening limiters, within which to disable the
Programming of positions
Position search
Motor type
Bluebus search
CONTROL UNIT FUNCTIONS
Intelligent Security & Fire Ltd.
