manualshive.com logo in svg

Nextron MASTERTRACE, Operating Manual, Page: 81 / 110

Share
Download
Nextron MASTERTRACE Operating Manual Download Page 81

MASTER

TRACE

B.4

Appendix B Display Message

Details - Measured

MESSAGE NO:

M2-05

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 100.0 A

DISPLAY MODE: Advanced

RESTRICTIONS: Single-Phase Modules

The displayed value is the highest Heater Current since the last reset. The
maximum value range for internal switching modules is 30.0 A. If the displayed
value is “O.L.”, a value greater than the maximum range was recorded. To reset the
displayed value press [RESET]. To reset with all statistics use RESET
STATISTICS function.

MESSAGE NO:

M2-06

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 100.0 A

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules

The displayed value is the highest Heater Current-A since the last reset. If the
displayed value is “O.L.”, a value greater than the maximum range was recorded.
To reset the displayed value press [RESET]. To reset with all statistics use RESET
STATISTICS function.

MESSAGE NO:

M2-07

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 100.0 A

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules

The displayed value is the highest Heater Current-B since the last reset. If the
displayed value is “O.L.”, a value greater than the maximum range was recorded.
To reset the displayed value press [RESET]. To reset with all statistics use RESET
STATISTICS function.

MESSAGE NO:

M2-08

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 100.0 A

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules

The displayed value is the highest Heater Current-C since the last reset. If the
displayed value is “O.L.”, a value greater than the maximum range was recorded.
To reset the displayed value press [RESET]. To reset with all statistics use RESET
STATISTICS function.

MESSAGE NO:

M2-09

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 1000 mA

DISPLAY MODE: Advanced

RESTRICTIONS: None

The displayed value is the highest Ground Fault Current since the last reset. If the
displayed value is “O.L.”, a value greater than the maximum range was recorded.
To reset the displayed value press [RESET]. To reset with all statistics use RESET
STATISTICS function.

MESSAGE NO:

M2-10

APPLIES TO:

Selected Heater

DEFAULT VALUE: N/A

VALUE RANGE: 0 to 1000 MWh

DISPLAY MODE: Advanced

RESTRICTIONS: None

The displayed value is the energy used in the last day. Energy is calculated from
the Heater Current times the Heater Voltage integrated over time. This value is
automatically updated once every 24 hours. It cannot be reset.

MAX HEATER CURRENT

4.7A 

&

A: MAX HEATER CURRENT

4.7A 

&

B: MAX HEATER CURRENT

4.7A 

&

C: MAX HEATER CURRENT

4.6A 

&

MAX GROUND FAULT

CURRENT: 6mA 

&

ENERGY USED LAST

DAY: 2.1kWh 

&

Summary of Contents for MASTERTRACE















































































































Reviews:

No comments