Nextron MASTERTRACE, Operating Manual

Page: 47 / 110

MASTER TRACE
5.11
Chapter 5 Operation
5.5 Setpoint Values Menu: Three-Phase Modules (1- and 5-point only)
SETPOINTS:
OPERATING VALUES
[MESSAGE
ô
]
SELECT HT:1-1
?
NONAME
&
[MESSAGE
ô
]
HEATER ENABLED?
yes
?
[MESSAGE
ô
]
HEATER SETPOINT:
5°C
?
[MESSAGE
ô
]
LOW TEMPERATURE
ALARM: 2°C
?
[MESSAGE
ô
]
HIGH TEMPERATURE
ALARM: off
?
[MESSAGE
ô
]
A: LOW CURRENT
ALARM: off
?
[MESSAGE
ô
]
C: HIGH CURRENT
ALARM: off
?
[MESSAGE
ô
]
[SETPOINT]
ò
1
[SETPOINT]
ò
SETPOINTS:
HEATER SETUP
[MESSAGE
ô
]
SELECT HT: 1-1
?
NONAME
&
[MESSAGE
ô
]
HTR 1-1 NAME:
NONAME
?
[MESSAGE
ô
]
MASTER OVERRIDE:
off
?
[MESSAGE
ô
]
PROPORTIONAL
CONTROL: off
?
[MESSAGE
ô
]
DEADBAND
2 C°
?
[MESSAGE
ô
]
IF RTD FAILS
HEATER GOES: off
?
[MESSAGE
ô
]
RTD MODE:
2 RTDs, lowest
?
[MESSAGE
ô
]
[SETPOINT]
3
4
ò
DISPLAY MODE:
normal user
?
[MESSAGE
ô
]
DEFAULT DISPLAY:
system status
?
[MESSAGE
ô
]
DISPLAY TIMEOUT:
60 seconds
?
[MESSAGE
ô
]
SCAN TIME:
3 seconds
?
[MESSAGE
ô
]
TEMPERATURE
UNITS: celcius
?
[MESSAGE
ô
]
COST PER kWh:
$0.05
?
[MESSAGE
ô
]
STAGGER START:
off
?
[MESSAGE
ô
]
NUM OF AMB SENSE
HTRS: 0
?
[MESSAGE
ô
]
SETPOINTS:
SYSTEM SETUP
[MESSAGE
ô
]
MODULE RANGE:
1-30
?
[MESSAGE
ô
]
MODULE LIST:
MOD: 1
?
SEL:yes
?
[MESSAGE
ô
]
[SETPOINT]
ò
6
MANUAL SYSTEM:
ALARM: disabled
?
[MESSAGE
ô
]
GF TEST:
test now
?
[MESSAGE
ô
]
go to 1
SETPOINTS:
SETPOINTS TEST
[MESSAGE
ô
]
MANUAL ALARM:
disabled
?
[MESSAGE
ô
]
MANUAL HEATER:
disabled
?
[MESSAGE
ô
]
RESET CONTROL
MODULE? no
?
[MESSAGE
ô
]
RESET MR100:
no
?
[MESSAGE
ô
]
MANUAL VERSION:
1501-0006_1
[MESSAGE
ô
]
FOR ASSISTANCE:
(403) 735-9555
[MESSAGE
ô
]
go to 6
5
Restrictions
1 5- & 10-point Modules
2 MR100 Interface Module
Advanced User Mode
2
2
2
2
2
READ MODULE
NUMBER: 1
?
[MESSAGE
ô
]
ALARM CONTACTS:
MECH: NC
?
SS: NC
?
[MESSAGE
ô
]
2
2
ð ð ð
GROUND FAULT
TRIP: 30mA
?
[MESSAGE
ô
]
TRACECHECK HTR ON
TIME: 0.5 MIN
?
[MESSAGE
ô
]
HEATER VOLTAGE:
120V
?
[MESSAGE
ô
]
go to 3
2
B: HIGH CURRENT
TRIP: off
?
[MESSAGE
ô
]
B: HIGH CURRENT
ALARM: off
?
[MESSAGE
ô
]
A: HIGH CURRENT
ALARM: off
?
[MESSAGE
ô
]
C: LOW CURRENT
ALARM: off
?
[MESSAGE
ô
]
B: LOW CURRENT
ALARM: off
?
[MESSAGE
ô
]
COPY TO OTHER
HEATERS: no
?
[MESSAGE
ô
]
go to 4
1
FIRMWARE VERSION:
D1-02-01
[MESSAGE
ô
]
SET MODULE
NUMBER: no
?
[MESSAGE
ô
]
BAUD RATE 1:
1200
?
[MESSAGE
ô
]
go to 5
MR100 BAUD RATE:
1200
?
[MESSAGE
ô
]
RTD BOARD:
On Board
?
[MESSAGE
ô
]
A: HIGH CURRENT
TRIP: off
?
[MESSAGE
ô
]
TRACECHECK CYCLE
TIME: off
?
[MESSAGE
ô
]
GROUND FAULT
ALARM: 20mA
?
[MESSAGE
ô
]
POWER LIMIT
CURRENT: off
?
[MESSAGE
ô
]
1
C: HIGH CURRENT
TRIP: off
?
[MESSAGE
ô
]
go to 2
1
ALARM LIGHT MODE:
alarm off
?
[MESSAGE
ô
]
AMBIENT SENSING
HEATER: None
?
[MESSAGE
ô
]
2
1
BAUD RATE 2:
1200
?
[MESSAGE
ô
]
AMBIENT RTD
TEMP: 5°C
&
[MESSAGE
ô
]
2