manualshive.com logo in svg

Nextron MASTERTRACE, Operating Manual

The Nextron MASTERTRACE Operating Manual is a comprehensive guide designed to help users make the most of their product. Download this essential manual free from manualshive.com and access detailed instructions and troubleshooting tips to optimize your experience with the Nextron MASTERTRACE.

Share
Download
background image

A.4

MASTER

TRACE

Appendix A Display Message

Details - Setpoints

MESSAGE NO:

S1-15

APPLIES TO:

Selected Heater

DEFAULT VALUE: off

VALUE RANGE: 0.5 to 100.0 A, off

DISPLAY MODE: Advanced

RESTRICTIONS: Single-Phase Modules

This function sets the High Current Trip setpoint. It must be greater than the Low
Current Alarm and the High Current Alarm setpoints. To disable this trip function
set the value to “off”. When the Heater Current is greater than or equal to this
setpoint, the heater circuit is opened, a High Current Trip Alarm is activated and a
“HIGH CURRENT TRIP” message is added to the System Status messages. This
is a latching alarm. When the cause of the alarm has been corrected, locate the
alarm message in the Status Menu and press [RESET]. The value range is in 0.5 A
increments. The maximum value for internal switching Control Modules is 30 A.

MESSAGE NO:

S1-16

APPLIES TO:

Selected Heater

DEFAULT VALUE: off

VALUE RANGE:

0.5 to 100.0 A, off

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules

This function sets the phase “A” High Current Trip setpoint. It must be greater
than the Low Current-A Alarm and the High Current-A Alarm setpoints. To
disable this trip function set the value to “off”. When the Heater Current-A is
greater than or equal to this setpoint, the heater circuit is opened, a High Current-A
Trip Alarm is activated and a “HIGH CURRENT-A TRIP” message is added to the
System Status messages. This is a latching alarm. When the cause of the alarm has
been corrected, locate the alarm message in the Status Menu and press [RESET].
The value range is in 0.5 A increments.

MESSAGE NO:

S1-17

APPLIES TO:

Selected Heater

DEFAULT VALUE: off

VALUE RANGE:

0.5 to 100.0 A, off

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules

This function sets the phase “B” High Current Trip setpoint. It must be greater
than the Low Current-B Alarm and the High Current-B Alarm setpoints. To
disable this trip function set the value to “off”. When the Heater Current-B is
greater than or equal to this setpoint, the heater circuit is opened, a High Current-B
Trip Alarm is activated and a “HIGH CURRENT-B TRIP” message is added to the
System Status messages. This is a latching alarm. When the cause of the alarm has
been corrected, locate the alarm message in the Status Menu and press [RESET].
The value range is in 0.5 A increments.

MESSAGE NO:

S1-18

APPLIES TO:

Selected Heater

DEFAULT VALUE: off

VALUE RANGE: 0.5 to 100.0 A, off

DISPLAY MODE: Advanced

RESTRICTIONS: Three-Phase Modules Only

This function sets the phase “C” High Current Trip setpoint. It must be greater
than the Low Current-C Alarm and the High Current-C Alarm setpoints. To
disable this trip function set the value to “off”. When the Heater Current-C is
greater than or equal to this setpoint, the heater circuit is opened, a High Current-C
Trip Alarm is activated and a “HIGH CURRENT-C TRIP” message is added to the
System Status messages. This is a latching alarm. When the cause of the alarm has
been corrected, locate the alarm message in the Status Menu and press
[RESET].The value range is in 0.5 A increments.

HIGH CURRENT

TRIP: off 

?

A: HIGH CURRENT

TRIP: off 

?

B: HIGH CURRENT

TRIP: off 

?

C: HIGH CURRENT

TRIP: off 

?

Summary of Contents for MASTERTRACE















































































































Reviews:

No comments

Related manuals for MASTERTRACE

H3C WX5500H series User Configuration Manual preview
WX5500H series
Brand: H3C Pages: 57
Jeep Liberty Instruction Sheet preview
Liberty
Brand: Jeep Pages: 32
Accel 300+ Installation Instructions Manual preview
300+
Brand: Accel Pages: 8
Jäger ADwin-Gold Hardware Manual preview
ADwin-Gold
Brand: Jäger Pages: 50
u-blox M8 Series Hardware Integration Manual preview
M8 Series
Brand: u-blox Pages: 28
u-blox EVK-NINA-W151 Quick Start preview
EVK-NINA-W151
Brand: u-blox Pages: 2
fadini ZERO.SAPE Manual preview
ZERO.SAPE
Brand: fadini Pages: 28
GEA VESTA Operating Instructions Manual preview
VESTA
Brand: GEA Pages: 47
V2 WES-EASY Manual preview
WES-EASY
Brand: V2 Pages: 48
Absima CR9T Quick Start preview
CR9T
Brand: Absima Pages: 5
GBD BE24G Installation Instructions Manual preview
BE24G
Brand: GBD Pages: 60
Xylem LOWARA Aquavara IPC Quick Start Manual preview
LOWARA Aquavara IPC
Brand: Xylem Pages: 292
Tenpilot TP06 3Rw Quick Start Manual preview
TP06 3Rw
Brand: Tenpilot Pages: 2
Lab-T SLX Nano User Manual preview
SLX Nano
Brand: Lab-T Pages: 17
Danfoss AME 15 QM Instructions Manual preview
AME 15 QM
Brand: Danfoss Pages: 14
YASKAWA CIMR-VC*****H**-00 series Quick Start Manual preview
CIMR-VC*****H**-00 series
Brand: YASKAWA Pages: 32
LEGRAND MRD6 v2 Installation Instructions Manual preview
MRD6 v2
Brand: LEGRAND Pages: 10
Hakko Electronics FG-100 Calibration Instructions preview
FG-100
Brand: Hakko Electronics Pages: 2

Brands by name

Popular brands

Load more brands