Nextron MASTERTRACE Page 31 Operating Manual Download

Page: 31 / 110

3.18

MASTER

TRACE

Chapter 3 Product Description

3.3.17 MR100 for Wondows CE Touch Screen Group
Interface Module

Control Power

Power Requirements:

10VA @ 120Vac, 50 or 60Hz

Communications

Ports:

1 Serial network connections

Type:

RS485

Protocol:

Modbus® RTU.

Transmission Rate:

600, 1200, 2400, 4800, 9600 baud.

Interconnect:

2-wire, shielded, twisted pair.

Highway Distance:

4,000 feet without repeater.

Modules per Highway:

(1) MR100 for Windows CE and (30)

Control Modules.

Environment

Approval:

FCC Part 15, Subpart B, Class A
CE EN-55022, EN-55024 and EN-
60950-1
UL 508, CSA-C22.2
Class1, Div.II, Groups A,B,C,D
ISA 12.12.01 (UL1604)

Operating Range:

-30°C to +70°C

(Storage: -40°C to +85°C)
Sealing:

Nema-4X, IP66 (front panel only)

Alarm

Alarm Output:

One NO dry mechanical contact

Alarm Output Rating:
Hazardous Areas:

Dry mech contact: 30Vdc/10mA max

250Vac/0.25A max

(not subject to a corrosive environment)

Ordinary Areas:

Dry mech contact: 120Vac/0.5A max

30Vdc/0.1A max

Alarm Light Output:

LED Indicator: 12Vdc/30mA

Alarm Messages:

Refer to Control Module Specifications

User Interface

Touch Screen:

7” touch screen, 800x480 WVGA, TFT
color LCD, Windows CE on-screen
keyboard

Bezel

Housing Material:

Polymer

Mounting:

For mounting on NEMA-4/4X

enclosure door. Includes gasketing.

Summary of Contents for MASTERTRACE















































































































Search results

Summary of Contents for MASTERTRACE

Reviews:

Related manuals for MASTERTRACE

Brands by name

Popular brands

Nextron MASTERTRACE, Operating Manual

Search results

Summary of Contents for MASTERTRACE

Reviews:

Related manuals for MASTERTRACE

Brands by name

Popular brands