manualshive.com logo in svg

Nextron MASTERTRACE, Operating Manual, Page: 72 / 110

Share
Download
Nextron MASTERTRACE Operating Manual Download Page 72

A.12

MASTER

TRACE

Appendix A Display Message

Details - Setpoints

Configures the alarm contacts for normally open (NO) or normally closed (NC).
MECH refers to the mechanical alarm contacts on terminals 6 and 7of the Control
Module and terminals 904 and 905 of the MR100 Interface Module. SS refers to
the solid-state dc alarm contacts on terminals 4 and 5 of the Control Module and
terminals 906 and 907 of the MR100 Interface Module. In NO mode, contact
closes during alarm condition. In NC mode, contacts open during alarm
condition.

MESSAGE NO:

S3-20

APPLIES TO:

Interface Module

DEFAULT VALUE:  1

VALUE RANGE: 1-254

DISPLAY MODE: Advanced

RESTRICTIONS: ML100 Interface Module

This function changes the Module Number of the Control Module connected to
the ML100 Interface.

MESSAGE NO:

S3-21

APPLIES TO:

Address Enabled Control
Module

DEFAULT VALUE: no

VALUE RANGE:yes, no

DISPLAY MODE:

Advanced

RESTRICTIONS: MR100 Interface Module

This function resets all values of the Control Module which has been placed in
Address Enabled mode. Select “yes” to proceed. Select “yes” again to confirm.
This message asks you to confirm that the Control Module Address is “enabled”.
The Control Module Address light must be on. Press [MSSG 

ò

] to proceed. Refer

Chapter 5.1.2.

MESSAGE NO:

S3-21a

 APPLIES TO:

Address Enabled Control
Module

DEFAULT VALUE: None

VALUE RANGE:

None

DISPLAY MODE: Advanced

RESTRICTIONS: MR100 Interface Module

This message provides a last chance to confirm the Reset Module function. Press
[MSSG 

ò

] to continue.

CONT - MSSG DOWN

ABORT - RESET

ô

SET ADDR ENABLE

ADDRESS LED ON

yes [STORE]

ARE YOU SURE?

no 

?

yes [STORE]

ABOUT TO RESET

MODULE

CONT - MSSG DOWN

ABORT - RESET

ô

[MSSG

ò

]

MODULE RESET

PRESS MSSG DOWN

TO CONTINUE

ô

[MSSG

ò

]

RESET CONTROL

MODULE?  no 

?

SET MODULE

NUMBER: 1 

?

Summary of Contents for MASTERTRACE















































































































Reviews:

No comments