Nexo NXAMP4x1mk2 User Manual Download Page 11 | Manualshive

Page: 11 / 70

background image

INTRODUCTION

NXAMPMK2 USER MANUAL

PAGE 11 / 70

Air flow of the NXAMPmk2 is from front to back, thus installation can mix DTDAMP (with DTD Controller),
first generation NXAMP and NXAMPmk2 in the same rack, all using the same air flow direction.

SPEAKER CABLE CHOICE

WARNING!

High voltage can be present on the power amplifier output terminals. Use at least NEC (National Electrical
Code) UL13 CL3 (under 300V) wiring cable to connect the NXAMPmk2 to the NEXO speakers.

To minimize power and damping factor losses in speaker cable, use suitable gauges from the table below.

Load Impedance (Ohms)

2

2.6

4

8

Cable section

Maximum length in meters (feet)

2.5 mm2 (AWG #13)

20 (66)

28 (92)

40 (130)

80 (260)

4 mm2 (AWG #11)

32 (105)

40 (130)

64 (210)

128 (420)

6 mm2 (AWG #9)

48 (160)

64 (210)

96 (315)

192 (630)

FRONT PANEL DESCRIPTION

The NXAMPmk2 features a color 4.3 inches touch screen display and a pushable rotary encoder with a
surround backlight.

A: AIR INTAKES

The NXAMPmk2 uses forced-air cooling. The variable speed cooling fan draws air in from the front and
exhausts it through the rear. Please be sure that you do not block the air intakes or exhaust vents.

B: 4.3 INCHES COLOR TOUCH SCREEN

The large tactile screen is used for the display of the amplifier settings and status. Use the Up/Down arrow
to navigate into the menus, select an area to adjust a parameter and turn or press the encoder accordingly.

C: ROTARY ENCODER

«
...
9
10
11
12
13
...
»

Summary of Contents for NXAMP4x1mk2







































































Reviews:

No comments

Related manuals for NXAMP4x1mk2

Brand: Parasound Pages: 72

Brand: Jafar Pages: 15

Brand: EasyIO Pages: 12

Brand: RMG Pages: 6

Brand: rada Pages: 16

Brand: Salda Pages: 20

Brand: Jäger Pages: 50

Brand: Dantherm Pages: 20

UNDER CONTROL CP-30A PILOT

Brand: G-Force Pages: 2

Brand: Watts Pages: 17

Brand: Dantel Pages: 6

GAMMA VERSUS Series

Brand: JCM Pages: 111

767-4804/000-800

Brand: WAGO Pages: 80

Brand: tell Pages: 11

Brand: Nordelettronica Pages: 8

Brand: Atari Pages: 3

Brand: Konig Pages: 47

Brand: Argo-Hytos Pages: 38

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands