Newland NLS-HR15XX-30 User Manual Download

Page: 29 / 104

【

Start Setup

】

【

Exit Setup

】

In the sensing reading mode, the scanner can set the reading time. in the unit of 1 second, the parameter rangs from

0-15sec, 0 means non-stop. The scanner also can set the time interval in the interval reading mode (stable sensing reading

time). Interval time is in the unit of 500ms, which can be set in 15 levels (from 01-15).

【

Set the Barcode Reading Time

】

【

Set the Scanning Time Intervals

】

The customer can select the sensitity according to the environmrnt, in order to increase the reading efficiency.

【

High Sensitivity

】

【

Low Sensitivity

】

【

Medium Sensitivity

】

【

Custom Sensitivity

】

Sensitivity Setup in the Sense Mode

It can be set in 16 levels from 0 to F, the samller the value, the higher the sensibility.

Example:

The steps of set the sensibility to level 5.

1. Read the

“Start Setup”barcode.

2. Read

the “Custom Sensibility” barcode.

3. Read the numeric

“5” barcode.

4. Read the

“Exit Setup” barcode.

Continuous Reading Mode

The device going to continuous reading without triggered. After successful barcode reading, the scanner will become

standby, and keep doing same loop.

Summary of Contents for NLS-HR15XX-30









































































































Search results

Summary of Contents for NLS-HR15XX-30

Reviews:

Related manuals for NLS-HR15XX-30

Brands by name

Popular brands

Newland NLS-HR15XX-30, User Manual

Search results

Summary of Contents for NLS-HR15XX-30

Reviews:

Related manuals for NLS-HR15XX-30

Brands by name

Popular brands