NETGEAR CG834WG User Manual Download | Manualshive

Page: 60 / 64

background image

Wireless Cable Modem Gateway CG834WG User Manual

A-2

v1.0, October 2007

Factory Default Settings

You can use the reset button located on the rear panel of your gateway to reset all settings to their
factory defaults. This is called a hard reset. To perform a hard reset, push and hold the reset button
for 5 seconds. The gateway will reboot and return to the settings shown in the following table.

Operating Frequency Ranges:

2.412~2.462 GHz (US)
2.412~2.472 GHz (Japan)
2.412~2.472 GHz (Europe ETSI)

Encryption:

40-bit (also called 64-bit), 128-bit WEP data encryption,

WPA-PSK(TKIP), and WPA2-PSK(AES)

Table A-1. Default Configuration Settings

Feature

Default Behavior

Gateway Login

User login URL

http://192.168.0.1

User name (case sensitive)

admin
superuser

Login Password (case sensitive)

password

Local Network (LAN)

LAN IP

192.168.0.1

Subnet mask

255.255.255.0

RIP direction

None

RIP version

Disabled

RIP authentication

None

DHCP server

Enabled

DHCP starting IP address

192.168.0.10

DHCP Ending IP Address

192.168.0.19

DMZ Disabled

Time zone

GMT

Time Zone Adjusted for Daylight Saving
Time

Disabled

SNMP

Disabled

«
...
58
59
60
61
62
...
»

Summary of Contents for CG834WG

































































Reviews:

No comments

Related manuals for CG834WG

OnSite 1052 Series

Brand: Patton electronics Pages: 20

Brand: Black Box Pages: 8

Brand: jablotron Pages: 2

Brand: Kathrein Pages: 16

Brand: ORANGE Pages: 12

Brand: GE Pages: 148

Brand: Corecess Pages: 14

Brand: PPL Pages: 2

Merlin for GPRS G201

Brand: Novatel Pages: 54

Brand: Ebyte Pages: 41

Brand: Lantronix Pages: 56

Brand: NETGEAR Pages: 28

Brand: NETGEAR Pages: 29

Brand: ERE Wireless Pages: 20

RC802-30B-FV35-S1

Brand: Raisecom Pages: 21

Brand: Paradise Datacom Pages: 231

Brand: D-Link Pages: 16

Brand: 3One data Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands