NETGEAR CG834WG User Manual Download

Page: 40 / 64

Wireless Cable Modem Gateway CG834WG User Manual

4-2

v1.0, October 2007

The Gateway Status screen fields are explained in the following table.

Table 4-1. Gateway Status Fields

Field

Description

Information

Standard Specification
Compliant

The specification to which the gateway’s cable interface is
compatible.

Hardware Version

The hardware version of the gateway.

Software Version

The software version of the gateway.

Cable Modem MAC Address

The MAC address used by the cable modem port of the
gateway. This MAC address may need to be registered with
your Cable Service Provider.

Device MAC Address

The MAC address of the router side of the gateway. This is the
equivalent of your PC when connected to a cable modem. You
can use the MAC Cloning feature to replace this MAC address
with another address when sending packets to the WAN.

Cable Modem Serial Number The serial number of the gateway hardware.

CM Certificate

If the Cable Modem certificate is Installed, it is possible for the
service provider to upgrade your Data Over Cable service
securely.

Status

System Up Time

This is the time since the gateway has registered with your
cable service provider.

Network Access

This field will change to Allowed when the registration with your
cable service provider is complete.

Cable Modem IP Address

The IP address of you gateway, as seen from the Internet.

Summary of Contents for CG834WG

































































Search results

Summary of Contents for CG834WG

Reviews:

Related manuals for CG834WG

Brands by name

Popular brands

NETGEAR CG834WG, User Manual

Search results

Summary of Contents for CG834WG

Reviews:

Related manuals for CG834WG

Brands by name

Popular brands